Supero SuperWorkstation 5038AD-T Скачать руководство пользователя страница 63

Страница: 63 / 130

Chapter 5: Advanced Serverboard Setup

5-23

PCI Slot_SMB Enable

Jumper Settings

Jumper Setting Defi nition

Closed

Enabled

Open

Disabled

PCI Slot SMB Enable (I

C1/I

C2)

Use jumpers I

C1/I

C2 to enable PCI

SMB (System Management Bus) sup-

port to improve system management

for the PCI slots. See the table on the

right for jumper settings.

Management Engine (ME)

Recovery

Use jumper JPME1 to select ME

Firmware Recovery mode, which will

limit resource allocation for essential

system operation only in order to

maintain normal power operation and

management. In the single operation

mode, online upgrade will be available

via Recovery mode. See the table on

the right for jumper settings.

ME Recovery

Jumper Settings

Jumper Setting Defi nition

Pins 1-2

Normal (Default)

Pins 2-3

ME Recovery

Manufacturer Mode Select

Close pins 2 and 3 of jumper JPME2 to

bypass SPI fl ash security and force the

system to operate in the Manufacturer

Mode, allowing the user to fl ash the

system fi rmware from a host server for

system setting modifi cations. See the

table on the right for jumper settings.

ME Mode Select

Jumper Settings

Jumper Setting Defi nition

Pins 1-2

Normal (Default)

Pins 2-3

Manufacture Mode

BIOS Recovery (JBR1)

The BIOS Recovery (JBR1) is used to

enable or disable the BIOS Recovery

feature of the motherboard. Install

the jumper on pins 2-3 to begin the

recovery process. See Appendix D for

related information.

BIOS Recovery (JBR1)

Jumper Settings

Jumper Setting Defi nition

Pins 1-2

Normal (Default)

Pins 2-3

Recover

Содержание SuperWorkstation 5038AD-T



































































































































Результаты поиска

Содержание SuperWorkstation 5038AD-T

Отзывы:

Похожие инструкции для SuperWorkstation 5038AD-T

Бренды по названию

Популярные бренды

Supero SuperWorkstation 5038AD-T, Руководство пользователя

Результаты поиска

Содержание SuperWorkstation 5038AD-T

Отзывы:

Похожие инструкции для SuperWorkstation 5038AD-T

Бренды по названию

Популярные бренды