Supero SuperWorkstation 5038AD-T Скачать руководство пользователя страница 58

Страница: 58 / 130

5-18

uper

orkstation 5038AD-T User's Manual

HDMI Port

One HDMI (High-Defi nition Multimedia

Interface) is located next to the VGA

port on the I/O backpanel. This con-

nector is used to display both high

definition video and digital sound

through an HDMI capable display us-

ing a single HDMI cable (not included).

VGA Port

A VGA port is located next to the USB

ports 0/1 on the I/O backpanel. Use

this port to connect to a compatible

VGA display.

DVI Port

A DVI port is located just under the

VGA port on the I/O backpanel. Use

this port to connect to a compatible

DVI (Digital Visual Interface) display.

Ethernet Ports

Two Gigabit Ethernet ports (LAN1/

LAN2) are located next to the HD

Audio Connector on the I/O backpanel

to provide network connections. These

ports accept RJ45 type cables.

Note

Please refer to the LED Indicator

Section for LAN LED information.

LAN Ports

Pin Defi nition

Pin# Defi nition Pin# Defi nition

P2V5SB

SGND

TD0+

Act LED

TD0-

P3V3SB

TD1+

Link 100 LED
(Green, +3V3SB)

TD1-

Link 1000 LED
(Yellow, +3V3SB)

TD2+

Ground

TD2-

Ground

TD3+

Ground

TD3-

Ground

Содержание SuperWorkstation 5038AD-T



































































































































Результаты поиска

Содержание SuperWorkstation 5038AD-T

Отзывы:

Похожие инструкции для SuperWorkstation 5038AD-T

Бренды по названию

Популярные бренды

Supero SuperWorkstation 5038AD-T, Руководство пользователя

Результаты поиска

Содержание SuperWorkstation 5038AD-T

Отзывы:

Похожие инструкции для SuperWorkstation 5038AD-T

Бренды по названию

Популярные бренды