manualshive.com logo in svg

Supero SuperWorkstation 5037A-i2-MA015, Руководство пользователя

Поделиться
Скачать
Supero SuperWorkstation 5037A-i2-MA015 Скачать руководство пользователя страница 9

1-3

Chapter 1: Workstation Overview

1-3 Chassis 

Features

The 5037A-i2-MA015 is a workstation with Whisper Quiet operation. The following is 

a general outline of its main features. See Figure 1-3 for a front view of the chassis.

System Power

The 5037A-i2-MA015 features a single 900W Gold Level multi-outlet power supply 

with PMBus, ideal for use in a workstation environment.

SATA Support

The 5037A-i2-MA015 was designed to support four 3.5" SATA hard drives and 

four optional 2.5" hard drives.

Front Control Panel

The control panel on the 5037A-i2-MA015 provides you with system monitoring 

and control. LEDs indicate system power, HDD activity, network activity, overheat 

conditions and power supply failure. A main power button and a system reset but-

ton are also included.

Note: 

The power supply fail LED indicates the power supply fan has failed.

Cooling System

The 5037A-i2-MA015 has an innovative "Whisper Quiet" cooling design that pro-

vides suffi cient cooling at very low noise level - ideal for a workplace environment. 

The chassis includes one 12-cm exhaust fan located at the rear of the chassis, and 

one 12-cm optional system cooling fan in the middle of the chassis. 

The power supply has one internal fan for redundancy; if this fan fails, the power 

supply must be replaced.

Control Panel

JF1 contains header pins for various front control panel connectors. See Figure 1-1 

for the pin locations of the various front control panel buttons and LED indicators.  

Содержание SuperWorkstation 5037A-i2-MA015



















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды