Supero SuperWorkstation 5037A-i2-MA015 Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 50

Supero SuperWorkstation 5037A-i2-MA015 Скачать руководство пользователя страница 39

Appendix A: Software

A-1

Appendix A

Software

A-1 Operating

System

The 5037A-i2-MA015 supports the Windows 7 Professional 64-bit Operating Sys-

tem. This OS has been pre-installed to the system.

System Recovery Instructions

This computer includes a hidden partition which contains a backup of your factory

Windows installation. In case of a system failure, you can use this backup to restore

your computer to a working state in just a few minutes.

Since this backup resides on the same physical hard-disk as your current Windows

installation, a hardware failure of the hard-disk will prevent you from reinstalling

Windows. There are two different ways to initiate a system recovery of your system:

•

Trigger recovery from OS level (run FullRestore.exe)

•

Trigger recovery during system boot up (press F10 key).

Warning:

System Recovery will wipe all of your personal data and restore the system

to OOBE. You must have your CD-KEY from COA label ready before performing this

action. System Recovery is an automated, one-step process. Do not initiate a system

recovery unless you are prepared for a complete re-installation back to the factory

default installation.

Support

If you require technical help for any Operating System problems, please contact your

3rd party software vendor or Technical Support at Supermicro. Contact information

is provided in Chapter 1.

«
...
37
38
39
40
41
...
»

Содержание SuperWorkstation 5037A-i2-MA015



















































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды