Supero SUPER 370SSA Скачать руководство пользователя страница 61

Страница: 61 / 92

Chapter 4: BIOS

4-11

BIOS

BootUp Num Lock

This option is used to select the status of the Number Lock function on your

keyboard on bootup. The settings are On and Off.

BootUp CPU Speed

This option is used set the CPU speed to either High or Low.

PS/2 Mouse Support

This option specifies whether a PS/2 Mouse will be supported. Settings are

Enabled and Disabled.

Typematic Rate

Set this option to select the rate at which the computer repeats a key that

is held down. Settings are Fast and Slow. Fast:

This sets the rate the

computer repeats a key to over 20 times per second. Under normal opera-

tions, this setting should not be changed. Slow:

This sets the rate the

computer repeats a key to under 8 times per second.

Boot Settings Configuration

Quick Boot

This option allows the BIOS to skip certain tests that are normally perfomred

on boot up. You can disable the option to speed up boot time. The settings

are Disabled and Enabled.

Quiet Boot

If Disabled, this option will cause the normal POST messages to be dis-

played upon setup. When Enabled, the OEM logo is displayed instead of

the POST messages.

Add-On ROM Display Mode

Set this option to display add-on ROM (read-only memory) messages. The

settings for this option are Force BIOS and Keep Current. Force BIOS

allows the computer to force a third party BIOS to display during system

boot. Keep Current has the system display AMIBIOS information on bootup.

BIOS.

Содержание SUPER 370SSA





























































































Результаты поиска

Содержание SUPER 370SSA

Отзывы:

Похожие инструкции для SUPER 370SSA

Бренды по названию

Популярные бренды

Supero SUPER 370SSA, Руководство пользователя

Результаты поиска

Содержание SUPER 370SSA

Отзывы:

Похожие инструкции для SUPER 370SSA

Бренды по названию

Популярные бренды