Supero SUPER 370SSA Скачать руководство пользователя страница 19

Страница: 19 / 92

Chapter 1: Introduction

1-11

Introduction

Features of the 370SSA/370SSM Motherboard

CPU

•

Single Pentium

III FCPGA 500 MHz-1 GHz processors and Celeron

PPGA 333-500 MHz processors at 133/100/66 MHz front side bus
speeds

Note: Please refer to the support section of our web site for a complete listing of supported

processors. (http://www.supermicro.com/TechSupport.htm)

M e m o r y

•

Three 168-pin DIMM sockets to support up to 512 MB unbuffered

SDRAM. PC133 and PC100 SDRAM are fully supported.

Chipset

•

Intel 815 (370SSM)

•

Intel 815E (370SSA)

Expansion Slots

370SSA:

•

Six 32-bit PCI slots

•

One AGP Pro slot

•

One CNR (Communications and Network Riser Card) slot

•

1 GPA (Graphics Perfomance Accelerator, formerly known as AIMM)

slot

370SSM:

•

Two 32-bit PCI slots

•

One 4xAGP slot

•

One AMR (Audio Modem Riser) slot

•

1 GPA (Graphics Perfomance Accelerator, formerly called AIMM) slot

BIOS

•

4 Mb Firmware Hub AMI

Flash BIOS

•

APM 1.2, DMI 2.1, PCI 2.2, ACPI 1.0, Plug and Play (PnP)

PC Health Monitoring

•

Seven onboard voltage monitors for CPU core, chipset voltage, +3.3V,

5V and

12V

•

Four-fan status monitor with firmware/software on/off control

•

Environmental temperature monitor and control

Содержание SUPER 370SSA





























































































Результаты поиска

Содержание SUPER 370SSA

Отзывы:

Похожие инструкции для SUPER 370SSA

Бренды по названию

Популярные бренды

Supero SUPER 370SSA, Руководство пользователя

Результаты поиска

Содержание SUPER 370SSA

Отзывы:

Похожие инструкции для SUPER 370SSA

Бренды по названию

Популярные бренды