background image

4-3

Chapter 4: System Interface

Overheat/Fan  Fail:  When  this  LED  flashes  it  indicates  a  fan  failure.  When 

• 

continuously on (not flashing) it indicates an overheat condition, which may be 
caused  by  cables  obstructing  the  airflow  in  the  system  or  the  ambient  room 

temperature being too warm. 

4-3  Control Panel LEDs

The control panel located on the front of the SC815 chassis has up to five LEDs. 

These  LEDs  provide  critical  information  related  to  different  parts  of  the  system. 
This  section  explains  what  each  LED  indicates  when  illuminated  and  any  action 
that may be required. 

Universal Information LED: The Universal Information LED is used to indated 

• 

fan failure, power failure, overheat condition, or to identify the unit within a large 
rack installation. The feature requires a motherboard that supports the Universal 
Information LED.

When this LED blinks red quickly, it indicates a fan failure and when blinking red 

slowly a power failure. This LED will be blue when used for UID (Unit Identifier). 

When on continuously red, it indicates an overheat condition, which may be caused 

by cables obstructing the airflow in the system or the ambient room temperature 

being too warm. See the table below for descriptions of the LED states.

Figure 4-2: Universal Information LED States

Universal Information LED States

State                                           Indication  

Fast Blinking Red (1x/sec)

Fan Fail

Solid Red

CPU Overheat

Slow Blinking Red (1x/4 sec)

Power Fail

Solid Blue

Local UID Button Depressed

Blinking Blue

IPMI-Activated UID

Note: 

Deactivating the UID LED must be performed in the same way it was acti-

vated. (If the UID LED was activated via IPMI, you can only turn the LED off via 
IPMI and not with the UID button.)

Содержание SC815S-560





















































































Отзывы: