background image

Chapter 1: Introduction

1-9

1-2 Chipset 

Overview

The H8SSL-i2 serverboard is based on Serverworks' HT-1000 chipset, which func-

tions as a HyperTransport

TM

 SystemI/O

TM

 Hub.  The HT-1000 chipset provides high 

performance, scalability and reliability.  Its HyperTransport architecture reduces IO 

bottlenecks to improve overall system performance.  System memory controllers 

not part of the chipset but instead are integrated into the processors to decrease 

latency.

HT-1000 HyperTransport I/O Hub

The HT-1000 I/O hub interconnects the CPU/host bridge with the I/O bridge via a 

HyperTransport bus to provide an interface to the various subsystems including the 

Super I/O functions, the onboard graphics, the IDE controller and the USB ports.  

HyperTransport Technology

HyperTransport technology is a high-speed, low latency point to point link that was 

designed to increase the communication speed by a factor of up to 48x between 

integrated circuits.  This is done partly by reducing the number of buses in the 

chipset to reduce bottlenecks and by enabling a more effi cient use of memory in 

multi-processor systems.  The end result is a signifi cant increase in bandwidth 

within the chipset.   

Содержание H8SSL-i2





































































Отзывы: