Supero H8SSL-i2 Скачать руководство пользователя страница 57

Страница: 57 / 68

Chapter 4: BIOS

4-13

4-4 Boot

Menu

Boot Settings Conﬁ guration

Boot Device Priority

This feature allows the user to prioritize the sequence for the Boot Device with the

devices installed in the system.

Hard Disk Drives

This feature allows the user to prioritize the Boot sequence from available hard

drives.

Removable Drives

This feature allows the user to specify the Boot sequence from available remov-

able drives.

CD/DVD Drives

This feature allows the user to specify the boot sequence from available CDROM

drives.

4-5 Security

Menu

AMI BIOS provides a Supervisor and a User password. If you use both passwords,

the Supervisor password must be set ﬁ rst.

Change Supervisor Password

Select this option and press <Enter> to access the sub menu, and then type in

the password.

Change User Password

Select this option and press <Enter> to access the sub menu, and then type in

the password.

Boot Sector Virus Protection

This option is near the bottom of the Security Setup screen. Select "Disabled" to

deactivate the Boot Sector Virus Protection. Select "Enabled" to enable boot sector

protection. When "Enabled", AMI BIOS displays a warning when any program (or

virus) issues a Disk Format command or attempts to write to the boot sector of the

hard disk drive. The options are Enabled and

Disabled

Содержание H8SSL-i2





































































Результаты поиска

Содержание H8SSL-i2

Отзывы:

Похожие инструкции для H8SSL-i2

Бренды по названию

Популярные бренды

Supero H8SSL-i2, Руководство пользователя

Результаты поиска

Содержание H8SSL-i2

Отзывы:

Похожие инструкции для H8SSL-i2

Бренды по названию

Популярные бренды