Supero H8QGL-6F+ Скачать руководство пользователя страница 64

Страница: 64 / 84

4-6

H8QGL-6/iF+ SERVERBOARD USER'S MANUAL

IOMMU

This setting is used to disable or set the GART size in systems without AGP. Options

include Enabled and

Disabled

Memory Timing Parameters

This selects the which node's timing parameters to display. The only selection

for this option is

CPU Node 0

Clock Speed Information

Clock speed information for memory is displayed under this Northbridge Chipset

Confi rguration page. This information includes Memory CLK, CAS Latency (Tcl),

RAS/CAS Delay (Trcd), Row Precharge Time (Trp), Min Active RAS (Tras), RAS/

RAS Delay (Trrd), Row Cycle (Trc), Read to Precharge (Trtp), Write Recover

Time (Twr) and Memory Type.



SouthBridge Chipset Confi guration

SouthBridge Chipset Information

SouthBridge dhipset information is displayed at the top of this menu on the

SouthBridge chipset CIMx version used.

OHCI/EHCI HC Device Functions

These settings allow you to either

enable

or eisable functions for OHCI or EHCI

bus devices. Options are

Enabled

or Disabled.

USB 2.0 Controller Mode

Use this setting to confi gure the USB 2.0 Controller in either

Hi-Speed

(480 Mps)

or Full Speed

(12 Mps) mode.

Legacy USB Support

Select "Enabled" to enable the support for USB Legacy. Disable Legacy support if

there are no USB devices installed in the system. "Auto" disabled Legacy support

if no USB devices are connected. The options are Disabled, Enabled and

Auto





IDE/SATA Confi guration

OnChip SATA Channel

This setting allows you to

enable

or disable the OnChip SATA channel. Options

are

Enabled

or Disabled.

Содержание H8QGL-6F+





















































































Результаты поиска

Содержание H8QGL-6F+

Отзывы:

Похожие инструкции для H8QGL-6F+

Бренды по названию

Популярные бренды

Supero H8QGL-6F+, Руководство пользователя

Результаты поиска

Содержание H8QGL-6F+

Отзывы:

Похожие инструкции для H8QGL-6F+

Бренды по названию

Популярные бренды