Supermicro SuperServer E302-9A Скачать руководство пользователя страница 59

Страница: 59 / 116

Chapter 6: UEFI BIOS

ME Reset

When this feature is set to Enabled, it sends a notification when ME initiates a global

reset. The options are Disabled and

Enabled

PMC WDT

When this feature is Enabled, it sends a notification when the PMC watchdog timer

expires. The options are Disabled and

Enabled

ME Uncorr Error

When this feature is set to Enabled, it sends a notification when there is an uncorrect

able ME error. The options are Disabled and

Enabled

SYS_PWROK

This feature sends a notification when there is a system power failure. SYS_PWROK

informs the PCH that power to system components is stable. The options are

Disabled

and Enabled.

PMC Parity Error

Set this feature to Enabled to receive PMC parity error notifications. The options are

Disabled

and Enabled.

Return Power

Set this feature to Enabled for the system to power up within four seconds after an
ADR entry. The options are Disabled and

Enabled

Interleaving

Set this feature to Enabled for NVDIMM interleaving support. Interleaving is a technique
that increases memory speed. The options are

Disabled

and Enabled.

Restore

When this feature is set to Enabled, data is restored to NVDIMM after a system power-
up. The options are Disable and

Enabled

Erase & ARM

Select Enabled to enable erasing and arming of NVDIMM after data recovery. The op-
tions are Disabled and

Enabled

Содержание SuperServer E302-9A





















































































































Результаты поиска

Содержание SuperServer E302-9A

Отзывы:

Бренды по названию

Популярные бренды

Supermicro SuperServer E302-9A, Руководство пользователя

Результаты поиска

Содержание SuperServer E302-9A

Отзывы:

Бренды по названию

Популярные бренды