Supermicro SuperServer E200-8D Скачать руководство пользователя страница 3

Страница: 3 / 107

Preface

Preface

About this Manual

This manual is written for professional system integrators and PC technicians. It provides
information for the installation and use of the SuperServer E200-8D. Installation and
maintainance should be performed by experienced technicians only.

Please refer to the E200-8D server specifications page on our website for updates on

supported memory, processors and operating systems (

http://www.supermicro.com

Notes

For your system to work properly, please follow the links below to download all necessary
drivers/utilities and the user’s manual for your server.

•

Supermicro product manuals:

http://www.supermicro.com/support/manuals/

•

Product drivers and utilities:

ftp://ftp.supermicro.com

•

Product safety info:

http://www.supermicro.com/about/policies/safety_information.cfm

If you have any questions, please contact our support team at:

[email protected]

This manual may be periodically updated without notice. Please check the Supermicro website
for possible updates to the manual revision level.

Warnings

Special attention should be given to the following symbols used in this manual.

Warning!

Indicates high voltage may be encountered when performing a procedure.

Warning!

Indicates important information given to prevent equipment/property damage

or personal injury.

Содержание SuperServer E200-8D












































































































Результаты поиска

Содержание SuperServer E200-8D

Отзывы:

Похожие инструкции для SuperServer E200-8D

Бренды по названию

Популярные бренды

Supermicro SuperServer E200-8D, Руководство пользователя

Результаты поиска

Содержание SuperServer E200-8D

Отзывы:

Похожие инструкции для SuperServer E200-8D

Бренды по названию

Популярные бренды