Supermicro SuperServer E200-8D Скачать руководство пользователя страница 19

Страница: 19 / 107

Chapter 2: Maintenance and Component Installation

Chapter 2

Maintenance and Component Installation

This chapter provides instructions on installing and replacing main system components. To

prevent compatibility issues, only use components that match the specifications and/or part

numbers given.

Installation or replacement of most components require that power first be removed from the

system. Please follow the procedures given in each section.

2.1 Removing Power

Use the following procedure to ensure that power has been removed from the system. This
step is necessary when removing or installing non-hot-swap components or when replacing
a non-redundant power supply.

1. Use the operating system to power down the system.

2. After the system has completely shut down, disconnect the AC adapter power cord from

the power source.

3. Disconnect the power cord from the chassis.

Содержание SuperServer E200-8D












































































































Результаты поиска

Содержание SuperServer E200-8D

Отзывы:

Похожие инструкции для SuperServer E200-8D

Бренды по названию

Популярные бренды

Supermicro SuperServer E200-8D, Руководство пользователя

Результаты поиска

Содержание SuperServer E200-8D

Отзывы:

Похожие инструкции для SuperServer E200-8D

Бренды по названию

Популярные бренды