manualshive.com logo in svg

Supermicro SuperServer 510P-WT, Руководство пользователя, Страница: 78 / 113

Поделиться
Скачать
Supermicro SuperServer 510P-WT Скачать руководство пользователя страница 78

78

Chapter 6: Optional Components

12. 

Select specific disks for RAID with an [X].

• 

RAID0: Select at least two [2 - 24] disks 

• 

RAID1: Select only two disks

• 

RAID5: Select at least three [3 - 24] disks

• 

RAID10: Select only four disks

13.  Select 

Strip Size

 (Default 64KB).

14.  Select 

Create Volume

.

15.  If another RAID is needed, start again at step 6.

16.  Press [F4] to save and reboot.

Hot Swap Drives

Intel VMD enables hot-plug and hot-unplug for NVMe SSDs, whether from Intel or other 
manufacturers. Under vSphere ESXi, several steps are necessary to avoid potential stability 
issues. See the information at link [1] below.

Hot-unplug

1. Prevent devices from being re-detected during rescan:

 

esxcli storage core claiming autoclaim --enabled=false

2. Unmount the VMFS volumes on the device. Check [2] for details.

3. Detach the device. Check [3] for details.

4. Physically remove the device.

Status Indications

An LED indicator on the drive carrier shows the RAID status of the drive.

Drive Carrier Status LED Indicator

Status

State (red)

Normal function

Off

Locating

4Hz blink

Fault

Solid on

Rebuilding

1Hz blink

IBPI SFF 8489 Defined Status LED States

Содержание SuperServer 510P-WT


















































































































Отзывы:

Нет отзывов