manualshive.com logo in svg

Supermicro SuperServer 510P-WT, Руководство пользователя, Страница: 45 / 113

Поделиться
Скачать
Supermicro SuperServer 510P-WT Скачать руководство пользователя страница 45

45

Chapter 3: Maintenance and Component Installation

3.7 System Cooling

Five 4cm counter-rotating fans provide the cooling for the system. Each fan unit is actually 

made up of two fans joined back-to-back, which rotate in opposite directions. This counter-
rotating  action  generates  exceptional  airflow  and  works  to  dampen  vibration  levels.  The 

chassis provides two additional open fan housings, where an additional system fan may be 
added for optimal cooling.
Make sure the chassis top cover makes a good seal so the cooling air circulates properly 
through the chassis.

Figure 3-7. Fan Positions

1

5

4

3

2

Installing Fans

The SYS-510P-WT/WTR chassis includes five pre-installed fans. One additional open slot 

is available so that one more fan may be added if additional cooling is required. These fans 
are NOT redundant, hot-plug, and so must be replaced when they fail.
Fan speed is controlled by system temperature via IPMI. If a fan fails, the remaining fans 
will ramp up to full speed. Replace any failed fan at your earliest convenience with the same 
type and model (the system can continue to run with a failed fan).

1. Open the chassis while the system is running to determine which fan has failed. Never 

run the server for an extended period of time with the chassis open.

2. 

Turn off the power to the system and unplug the power cord from the power supply.

3. Remove the failed fan's wiring from the fan header on the serverboard.

4. Lift the failed fan from the chassis and pull it completely out.

Содержание SuperServer 510P-WT


















































































































Отзывы:

Нет отзывов