Supermicro SuperServer 5038MR-H8TRF Скачать руководство пользователя страница 115

Страница: 115 / 133

7-28

SuperServer 5038MR-H8TRF User’s Manual

settings.

IPMI Firmware Revision

This item indicates the IPMI firmware revision used in your system.

IPMI Status

This item indicates the status of the IPMI firmware installed in your system.



System Event Log

Enabling/Disabling Options

SEL Components

Select Enabled for all system event logging at bootup. The options are

Enabled

and Disabled.

Erasing Settings

Erase SEL

Select Yes, On next reset to erase all system event logs upon next system reboot.
Select Yes, On every reset to erase all system event logs upon each system reboot.

7-5 IPMI Settings

Use this feature to configure the Intelligent Platform Management Interface(IPMI)

Содержание SuperServer 5038MR-H8TRF






































































































































Результаты поиска

Содержание SuperServer 5038MR-H8TRF

Отзывы:

Похожие инструкции для SuperServer 5038MR-H8TRF

Бренды по названию

Популярные бренды

Supermicro SuperServer 5038MR-H8TRF, Руководство пользователя

Результаты поиска

Содержание SuperServer 5038MR-H8TRF

Отзывы:

Похожие инструкции для SuperServer 5038MR-H8TRF

Бренды по названию

Популярные бренды