Supermicro SuperServer 5038MR-H8TRF Скачать руководство пользователя страница 106

Страница: 106 / 133

Chapter 7: AMI BIOS

7-19

MMIOHBase

Use this item to select the base memory size according to memory-address map-
ping for the IO hub. The base memory size must be between 4032G to 4078G. The
options are

56T

, 48T, 24T, 512G, and 256G.\

MMIO High Size

Use this item to select the high memory size according to memory-address mapping
for the IO hub. The options are

256G

, 128G, 512G, and 1024G.

CPU1 MICRO-LP PCI-E 3.0 X8 SLOT OPROM, CPU1 SLOT1 PCI-E 3.0 X8

SLOT OPROM

Select Enabled to enable Option ROM support to boot the computer using a device

installed on the slot specified by the user. The options are Disabled, Legacy and EFI.

Onboard Video Option ROM

Use this item to select the Onboard Video Option ROM type. The options are

Legacy

and EFI.

VGA Priority

Use this item to select the graphics device to be used as the primary video display
at bootup. The options are

Onboard

and Offboard.

Network Stack

Select Enabled to enable PXE (Preboot Execution Environment) or UEFI (Unified

Extensible Firmware Interface) for network stack support. The options are

Enabled

and Disabled.



Super IO Configuration

Super IO Chip AST2400



Serial Port 1 Configuration/Serial Port 2 Configuration

Serial Port 1/Serial Port 2

Select Enabled to enable the onboard serial port specified by the user. The options

are

Enabled

and Disabled.

Device Settings

This item displays the base I/O port address and the Interrupt Request address of

a serial port specified by the user.

Содержание SuperServer 5038MR-H8TRF






































































































































Результаты поиска

Содержание SuperServer 5038MR-H8TRF

Отзывы:

Похожие инструкции для SuperServer 5038MR-H8TRF

Бренды по названию

Популярные бренды

Supermicro SuperServer 5038MR-H8TRF, Руководство пользователя

Результаты поиска

Содержание SuperServer 5038MR-H8TRF

Отзывы:

Похожие инструкции для SuperServer 5038MR-H8TRF

Бренды по названию

Популярные бренды