Supermicro Supero PDSML-LN1 Скачать руководство пользователя страница 48

Страница: 48 / 95

3-4

PDSML-LN1/PDSML-LN2

User's Manual

bootable device or USB pen to fl ash the BIOS. Then, your system will automati-

cally reboot. If you choose the .exe fi le, please run the .exe fi le under Windows to

create the BIOS fl ash fl oppy disk. Insert the fl oppy disk into the system you wish

to fl ash the BIOS. Then, bootup the system to the fl oppy disk. The BIOS utility will

automatically fl ash the BIOS without any prompts. Please note that this process

may take a few minutes to complete. Do not be concerned if the screen is paused

for a few minutes.

Warning

: Do not shut down or reset the system while updating BIOS

to prevent possible system boot failure!)

Question:

What's on the CD that came with my motherboard?

Answer:

The supplied compact disc has quite a few drivers and programs that will

greatly enhance your system. We recommend that you review the CD and install

the applications you need. Applications on the CD include chipset drivers for Win-

dows, security and audio drivers.

Question: How do I connect the ATA100/66 cable to my IDE device(s)?

Answer:

The 80-wire/40-pin high-density ATA100/66 IDE cable that came with

your system has two connectors to support two drives. This special cable must be

used to take advantage of the speed the ATA100/66 technology offers.

Connect

the blue connector to the onboard IDE header and the other connector(s) to

your hard drive(s).

Consult the documentation that came with your disk drive for

details on actual jumper locations and settings.

3-4 Returning Merchandise for Service

A receipt or copy of your invoice marked with the date of purchase is required be-

fore any warranty service will be rendered. You can obtain service by calling your

vendor for a Returned Merchandise Authorization (RMA) number. When returning

to the manufacturer, the RMA number should be prominently displayed on the

outside of the shipping carton, and mailed prepaid or hand-carried. Shipping and

handling charges will be applied for all orders that must be mailed when service

is complete.

This warranty only covers normal consumer use and does not cover damages in-

curred in shipping or from failure due to the alteration, misuse, abuse or improper

maintenance of products. For faster service, RMA authorizations may be requested

online (http://www.supermicro.com/support/rma/).

During the warranty period, contact your distributor fi rst for any product problems.

Содержание Supero PDSML-LN1
































































































Результаты поиска

Содержание Supero PDSML-LN1

Отзывы:

Похожие инструкции для Supero PDSML-LN1

Бренды по названию

Популярные бренды

Supermicro Supero PDSML-LN1, Руководство пользователя

Результаты поиска

Содержание Supero PDSML-LN1

Отзывы:

Похожие инструкции для Supero PDSML-LN1

Бренды по названию

Популярные бренды