Supermicro Supero PDSML-LN1 Скачать руководство пользователя страница 17

Страница: 17 / 95

Chapter 1: Introduction

1-11

SoftOff state, the ATX power supply provides power to keep the required circuitry

in the system "alive." In case the system malfunctions and you want to turn off the

power, just press and hold the power button for 4 seconds. The power will turn off

and no power will be provided to the motherboard.

Wake Ring-On (WOR)

Wake-up events can be triggered by a device such as the external modem ringing

when the system is in the SoftOff state. Note that external modem ring-on can only

be used with an ATX 2.01 (or above) compliant power supply.

Wake-On-LAN (WOL)

Wake-On-LAN is defi ned as the ability of a management application to remotely

power up a computer that is powered off. Remote PC setup, up-dates and asset

tracking can occur after hours and on weekends so that daily LAN traffi c is kept

to a minimum and users are not interrupted. The motherboard has a 3-pin header

(WOL) to connect to the 3-pin header on a Network Interface Card (NIC) that has

WOL capability. In addition, an onboard LAN controller can also support WOL

without any connection to the WOL header. The 3-pin WOL header is to be used

with a LAN add-on card only.

*Note

: Wake-On-LAN requires an ATX 2.01 (or above)

compliant power supply.

1-5

ACPI Features

ACPI stands for Advanced Confi guration and Power Interface. The ACPI specifi -

cation defi nes a fl exible and abstract hardware interface that provides a standard

way to integrate power management features throughout a PC system, including its

hardware, operating system and application software. This enables the system to

automatically turn on and off peripherals such as CD-ROMs, network cards, hard

disk drives and printers. This also includes consumer devices connected to the PC

such as VCRs, TVs, telephones and stereos.

In addition to enabling operating system-directed power management, ACPI

provides a generic system event mechanism for Plug and Play and an operating

system-independent interface for confi guration control. ACPI leverages the Plug

and Play BIOS data structures while providing a processor architecture-indepen-

dent implementation that is compatible with both Windows and Linux Operating

Systems.

Содержание Supero PDSML-LN1
































































































Результаты поиска

Содержание Supero PDSML-LN1

Отзывы:

Похожие инструкции для Supero PDSML-LN1

Бренды по названию

Популярные бренды

Supermicro Supero PDSML-LN1, Руководство пользователя

Результаты поиска

Содержание Supero PDSML-LN1

Отзывы:

Похожие инструкции для Supero PDSML-LN1

Бренды по названию

Популярные бренды