manualshive.com logo in svg

Supermicro SBI-7127R-S6, Руководство пользователя, Страница: 10 / 86

Поделиться
Скачать
Supermicro SBI-7127R-S6 Скачать руководство пользователя страница 10

SBI-7127R-S6 Blade Module User’s Manual

1-2

1-3

Blade Module Features

Table 1-1

 lists the main features of the SBI-7127R-S6 blade module. See the 

proceeding section for components typically included in a blade system and other 
optional components. Specific details for the SBI-7127R-S6 blade module are found in 

Chapter 4: "Blade Module Features" on page 4-1

.

Processors

The SBI-7127R-S6 blade module supports dual 2011-pin Socket R (LGA 2011) E5-2600 
series processors.

Refer to the Supermicro web site for a complete listing of supported processors (

http://

www.supermicro.com/products/superblade

). Please note that you will need to check the 

detailed specifications of a particular blade module for a list of the CPUs it supports.

Details on installation of the processor into the SBI-7127R-S6 blade module are found in 

Chapter 3: "Setup and Installation" on page 3-1

.

Memory

Both the SBI-7127R-S6 blade module have sixteen (16) 240-pin DIMM sockets that can 
support up to 512 GB RDIMM or 128 GB UDIMM of DDR3 1600/1333/1066/800 MHz 
speed, 32GB, 16GB, 8GB, 4GB, 2GB and 1GB size SDRAM memory. Memory is 
interleaved, which requires modules of the same size and speed to be installed in 
groups (of two or three). 

Please refer to the Supermicro web site for a list of supported memory 
(

www.supermicro.com/products/superblade

). The detailed specifications for a blade 

module will contain a link to a list of recommended memory sizes and manufacturers.

Table 1-1. SBI-7127R-S6 Blade Module Specification Features

Mainboard

B9DR7 (proprietary form factor)

Chassis Dimensions (HxWxD): 11.32" x 1.67" x 18.9" (288mm x 42.4mm x 
480mm)

Processors

Eight/six/four core Intel

™

 Xeon

®

 E5-2600 series 2011-pin processors. 

Please refer to our web site for a complete listing of supported processors.

FSB Speed

QPI up to 8 GT/s

Chipset

Intel C602J

Graphics Controller

Integrated Matrox G200 Graphics

BIOS

16 Mb SPI Flash EEPROM with AMI® BIOS

Memory Capacity

Supports up to 512 GB of RDIMM and 128 GB UDIMM SDRAM memory of 
DDR3 1600/1333/1066/800 MHz speed and 32GB, 16GB, 8GB, 4GB, 2GB 
and 1GB size in sixteen (16) 240-pin DIMM sockets

HDD Controller

LSI

™

 2208

®

 RAID controller 

Hard Drive Bays

Includes six hot-swap drive bays for 2.5" SATA/SAS/SSD disk drives

Содержание SBI-7127R-S6























































































Отзывы:

Нет отзывов