manualshive.com logo in svg

Supermicro MicroBlade MBI-6119G-C4, Руководство пользователя

Поделиться
Скачать
Supermicro MicroBlade MBI-6119G-C4 Скачать руководство пользователя страница 6

MBI-6119G-C4/T4 MicroBlade Modules User’s Manual

vi

Installing the Processor(s) ...................................................................... 3-4
Installing a Heatsink................................................................................ 3-6
Removing a Heatsink.............................................................................. 3-7

3-5 Memory Installation

........................................................................... 3-8

Populating Memory Slots ........................................................................ 3-8
DIMM Installation .................................................................................... 3-9

3-6 Hard Disk Drive Installation

............................................................. 3-9

3-7 Installing the Operating System

.................................................... 3-10

Installing via PXE Boot.......................................................................... 3-10
Installing via Virtual Media (Drive Redirection) ..................................... 3-10

Chapter 4 MicroBlade Module Features

................................. 4-1

4-1 Control Panel

..................................................................................... 4-2

Power Button .......................................................................................... 4-3
LED Indicators ........................................................................................ 4-3

4-2 Motherboard

....................................................................................... 4-4

Jumpers .................................................................................................. 4-7
CMOS Clear............................................................................................ 4-7

4-3 Blade Unit Components

................................................................... 4-8

Memory Support ..................................................................................... 4-9
Hard Disk Drives ..................................................................................... 4-9

Chapter 5 BIOS

....................................................................................... 5-1

5-1 Introduction

......................................................................................... 5-1

System BIOS .......................................................................................... 5-1
How To Change the Configuration Data ................................................. 5-1
Starting the Setup Utility ......................................................................... 5-1

5-2 BIOS Updates

.................................................................................... 5-2

5-3 Running Setup

................................................................................... 5-3

5-4 Main BIOS Setup

............................................................................... 5-4

5-5 Advanced Setup

................................................................................ 5-5

5-6 Event Logs Setup

............................................................................ 5-17

5-7 IPMI Setup

........................................................................................ 5-18

5-8 Security

............................................................................................. 5-20

5-9 Boot

................................................................................................... 5-22

5-10 Save & Exit

..................................................................................... 5-23

Содержание MicroBlade MBI-6119G-C4





















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды