Supermicro MicroBlade MBI-6119G-C2 Скачать руководство пользователя страница 38

Страница: 38 / 88

MBI-6119G-C2 MicroBlade Modules User’s Manual

3-6

Installing a Heatsink

An active type heatsink is used on the motherboard.

Note:

You should apply thermal grease to the heatsink if it has not already been

pre-applied.

1. Place the heatsink on top of the CPU so that the four mounting holes are aligned

with those on the heatsink retention mechanism.

2. Screw in two diagonal screws (i.e. the #1 and the #2 screws) until they are just

snug. Do not fully tighten the screws or you may damage the CPU.

3. Add the two remaining screws then finish the installation by fully tightening all four

screws (be careful not to overtighten).

Note:

The images above is for illustrative purposes only.

Screw #1

Motherboard

Mounting Holes

Heatsink Bracket

Screw #2

Содержание MicroBlade MBI-6119G-C2

























































































Результаты поиска

Содержание MicroBlade MBI-6119G-C2

Отзывы:

Бренды по названию

Популярные бренды

Supermicro MicroBlade MBI-6119G-C2, Руководство пользователя

Результаты поиска

Содержание MicroBlade MBI-6119G-C2

Отзывы:

Бренды по названию

Популярные бренды