The pilot is visible through the left hand side of ceramic fuel matrix. When cold, the coals or peb-
bles may be rotated for good viewing. The fire features a ‘twin spark’ ignition system to aid light-
ing, Push the control knob in fully and turn anti-clockwise through both of the SPARK positions,
keeping fully depressed, hold there for a few seconds. If the fire has not been used for some time,
hold the knob in this position for longer, to allow any air in the pipes to be purged.
Continue turning anti-clockwise through the spark clicks to the nine o’clock position, ensuring
the pilot has lit. If not, return the knob clockwise, and repeat. When the pilot lights after one of
the two sparks, keep the knob depressed in the nine o’clock position for approximately ten sec-
onds. Now release the knob and the pilot should stay alight. If the pilot is extinguished during
use, wait three minutes before repeating the ignition procedure.
To achieve the HIGH setting, push the control knob in slightly and continue turning anti-clock-
wise to the high position. The main burner should light after a few seconds. To decrease the set-
ting to LOW, push the knob in slightly and turn the control knob clockwise to the low setting. To turn to the pilot only position from
the HIGH or LOW positions, press the control knob in, and return to the nine o’clock position and release. To turn the fire OFF, keep
the knob pressed in, return to the off position and release.
The pilot is visible through the left hand side of the front ceramic strip.When cold, the coals or peb-
bles may be rotated for good viewing. Push the slide control knob fully downwards to the SPARK posi-
tion, and hold there for a few seconds, until the pilot light stays on. When the pilot light has established,
release the slide control knob and it will return to the LOW flame setting. If the pilot is extinguished
during use, wait three minutes before repeating the ignition procedure.
To achieve the HIGH setting, move the slide control knob upwards to the HIGH flame setting. The fire
can also be set to operate anywhere between HIGH and LOW by moving the control knob to an inter-
mediate position.
To turn the fire OFF, move the slide control knob upwards upwards fully to the position marked ‘O’.
The pilot is visible through the left hand side of the front ceramic strip. When cold,
the coals or pebbles may be rotated for good viewing. Turn the main burner con-
trol (shown on left hand side of control valve) knob fully anti-clockwise.
Turn ignition knob (shown on right hand side of control valve) slightly left towards
the ignition position until reaching the stop, press down and hold for 5 seconds
(only pilot gas is flowing)
Continue pressing down the knob while turning further to the left to activate the
piezo spark, continue to hold the knob down for a further 10 seconds after the
pilot has been lit. If the pilot does not light repeat the previous steps.
Upon lighting and after the further 10 seconds, release the knob and turn further to the left to the
ON position. The main burner will light and be controlled in accordance with the main burner con-
trol knob setting. Adjust the main burner control knob to the desired setting.
If the pilot is extinguished during use of the fire, you MUST wait ten minutes before repeating the
ignition procedure.
To turn the main burner OFF whilst keeping the pilot flame lit, turn the ignition control knob to the
pilot position then only the pilot will remain lit.
To shut the fire off completely, press the ignition control knob down and continue turning to the
right from the pilot position to the OFF position.
A safety interlock prevents re-ignition of the pilot flame until the thermocouple has cooled suffi-
ciently to allow the magnetic valve unit to reset itself.
The remote control unit allows operation of the main burner setting between maximum and pilot
only setting. It does not permanently turn the pilot on or off.
The remote control handset incorporates an inbuilt safety feature to prevent the main burner being
activated or turned up accidentally. It is necessary to press buttons 1 and 2 (see figure 4) simultane-
ously to turn the fire up.
To turn the fire down press button 3 only.
2
©
2011 Focal Point Fires plc.
4.0 OPERATING THE FIRE - MANUAL CONTROL MODELS
GB IE
4.1 OPERATING THE FIRE - SLIDE CONTROL MODELS
Figure 1
Figure 2
1
2
3
Figure 3
Figure 4
4.2 OPERATING THE FIRE - REMOTE CONTROL MODELS