SuperiorFireplaces.us.com
127020-01_E
5
FIREPLACE INSTALLATION
4. Check the level of the fireplace and shim with sheet metal if neces-
sary.
5. Before securing fireplace to prepared framing, the ember protector
(provided) must be placed between the hearth extension (not sup-
plied) and under bottom front edge of fireplace to protect against
glowing embers falling through. If fireplace is to be installed on a
raised platform, a Z-type ember protector (not supplied) must be
fabricated to fit your required platform height. The ember protec-
tor should extend under fireplace a minimum of 1
1
/
2
". The ember
protector should be made of galvanized sheet metal (28 gauge
minimum) to prevent corrosion.
6. Using screws or nails, secure fireplace to framing through flanges
located on sides of fireplace.
DRAIN PAN (DP36)
For outdoor installations, the fireplace enclosure must allow for
adequate drainage and fresh air ventilation. It is recommended that
a sealed, corrosion resistant catch pan with provision for drainage
be installed under the fireplace within the fireplace enclosure (see
Accessories on page 19).
41
3
/
4
"
(1061 mm)
41
3
/
4
"
(1061 mm)
21
7
/
8
"
(556 mm)
Figure 1 - Framing Dimensions
Figure 2 - Corner Installation
SELECTING LOCATION
WARNING: DO NOT INSTALL IN SLEEPING ROOM
OF MOBILE HOMES.
To determine the safest and most efficient location for the fireplace,
you must take into consideration the following guidelines:
1. The location must allow for proper clearances (see Figures 1 and
2).
2. Consider a location where the fireplace will not be affected by
drafts, air conditioning ducts, windows or doors.
3. A location that avoids the cutting of joists or roof rafters will make
installation easier.
4. An outside air kit is available with this fireplace (see Optional Outside
Air Kit on page 7).
MINIMUM CLEARANCE TO COMBUSTIBLES
Ceiling 40" (1016 mm) minimum
Back and sides of fireplace 3/4" (19 mm) minimum*
Floor**
0" (0 mm) minimum
Perpendicular wall to opening 12" (305 mm) minimum
Top spacers 0" (0 mm) minimum
Mantel clearances
see Mantels, page 6.
Chimney outer pipe surface
1" (26 mm) minimum
* Not required at nailing flanges
** See step 2 of Framing
WARNING: Do not pack required air spaces with
insulation or other materials.
Minimum/Maximum Chimney Height for Residential Installation
The minimum height of the chimney, measured from the base of
the fireplace to the flue gas outlet of the termination, is 14.5 feet for
straight flue or a flue with one elbow set. The maximum distance
between elbows is 6 feet. For systems with two elbow sets, the
minimum height is 22 feet. The maximum height of any system is
50 feet. This measurement includes the fireplace, chimney sections
and the height of the termination assembly at the level of the flue gas
outlet (see Figure 18, page 11).
Minimum/Maximum Chimney Height for Outdoor Installation
The minimum height of the chimney, measured from the base of the
fireplace to the flue gas outlet of the termination, is 7
1
/
2
feet (minimum
of 4 feet of chimney pipe sections required for outdoor installation).
FRAMING
1. Frame opening for fireplace using the dimensions shown in Figures
1 and 2.
2. If fireplace is to be installed directly on carpeting, tile or any
combustible material other than wood flooring, the fireplace must
be installed upon a metal or wood panel extending the full width
and depth of fireplace.
3. Set fireplace directly in front of this opening and slide unit back
until nailing flanges touch side framing.
Maintain
3
/
4
"
Clearance at
Sides and
Back of
Fireplace
3
/
4
" Clearance Not
Required at Nailing Flanges
24
1
/
2
"
(623 mm)
52
1
/
4
"
(1328 mm)
17
3
/
8
"
(442 mm)
73
7
/
8
" (1877 mm)
