background image

NOTE: DIAGRAMS & ILLUSTRATION ARE NOT TO SCALE.

12

Figure 11

Hood

Side View

FIREBOX FINISHES

There are a wide variety of “finished looks” for your built-in Vent-Free 

firebox from formal wall decor with elaborate mantels to rustic wood 

paneling or warm brick facings.

Only noncombustible materials like marble, stone, tile, brick, etc. may 

overlap the black front facing.  Seal all joints between the black facing 

and wall surrounds to prevent air intrusion. Use noncombustible caulking 

material only to seal the black metal facing to the surround material on 

the finished wall.  See Figures 3 and 23.

NOTE: No combustible material shall be allowed to 

overlap or contact any section of the front painted face.

HOOD KIT INSTALLATION

The firebox canopy (hood) shall not be modified or replaced with 

a canopy that may be provided with the unvented decorative 

room heater.

NOTE: A hood comes standard and is required for model VRT3232.  

The factory-supplied hood must be installed on the firebox for safe 

operation for model VRT3232 series in all installations (this part is 

optional for VRT3236 and VRT3242 models).  See 

Figure 11

.

These hood kits are design to be fitted to the face of the appliance directly 

above the firebox opening.  In addition to providing an aesthetically pleasing 

appearance to your appliance, the hood reduces heat effects to decora-

tive mantels and finish materials located directly above the fireplace and 

reduces the Mantel / Trim clearances (see Figure 4 on Page 7

).

Please read this entire manual and understood thoroughly before proceed-

ing with the installation of these kits. 

Step 1. Using a 5/16" nut driver or socket, remove the screen and rod 

assemblies as shown in Figure 10.

Step 2. Align the hood with the holes in the side frames as shown in 

Figure 11.  Install three screws as shown in Figure 11. Make 

sure hood is level and secure.

Step 3. Reinstall screen and rod assemblies

 (see

 Figure 10

).

Figure 10

Removing Screens and Rods:

Remove screws (see dotted 

lines). Pull out rods from 

locating holes on side of firebox 

opening.

Reinstalling Screens and Rods:

Insert rods into corresponding 

locating holes on sides of firebox 

opening, then reinstall screws 

as shown.

Содержание VRT3232WH

















Отзывы: