SuperiorFireplaces.us.com
126861-01P
17
GAS CONTROL MODULE SYSTEM
Continued
NOTE:
The module must be programmed to the Remote Control
transmitter.
• To program the module (make sure the system has power),
locate the learn button on left side as shown in
Figure 27, Page
16
. Press and release the learn button. There will be a beep
sound from the module. Then press any button on the remote
transmitter. Once the module's internal receiver accepts the
transmitter code, there will be a series of confirming beeps.
• The remote system is ready for use.
Figure 28 - Remote Control Battery Compartment
Figure 29 - Touch Screen Settings
BACK
Cont.
S M T W T F S
AM
PM
ROOM
SET
P1
A
B
P2
P2
AUX
P2
Pilot
:
OFF
ON
°
°
u
PROGRAM
USB
MODE/SET
BATTERY
COMPARTMENT
Cont.
S M T W T F S
AM
PM
ROOM
SET
P1
A
B
P2
P2
AUX
P2
Pilot
:
OFF
ON
°
°
u
PROGRAM
USB
MODE/SET
MODE Zone
LIGHT Zone
ROOM TEMP Zone
TIME/PROG. Zone
SET TEMP Zone (Unused)
AUX Zone (Unused)
FAN Zone (Unused)
DOWN Button
MODE/SET
Button
UP Button
FLAME Zone
REMOTE CONTROL OPERATION
NOTE:
Make sure the valve module and light module are plugged
into the electric duct assembly.
BATTERY BACK-UP
This fireplace is equipped with a battery back-up. If the power was
to go out on the fireplace, the battery back-up allows the fireplace to
remain operational. Make sure to periodically check the condition of
the four AA batteries used for the battery back-up.
This remote control system was developed to provide a safe, reliable,
and user-friendly remote control system. The system can be operated
manually from the transmitter.
The transmitter operates with (4) AAA 1.5V batteries that are included.
Install the batteries supplied with the unit into the battery compart-
ment. It is recommended that ALKALINE batteries always be used
for this product. Be sure the batteries are installed with the (+) and
(-) ends facing the correct direction.
When you start up the remote, if a low battery signal appears or if
the LCD screen does not illuminate when you touch it, check battery
position and if the batteries are fully charged.
TOUCH SCREEN LCD AND BUTTON LAYOUT
Functional Description
NOTE:
All function adjustments will be automatically accepted 15 -
seconds after pressing a given touch zone or button. The user may
press the MODE/SET button to immediately accept the adjustment
manually.
Day and Time Display
• The current day of week and time of day will be continuously dis-
played in the TIME/PROG Zone (except during Setup operations).
• The day of week will be displayed as one of the following: S,
M, T, W, T, F, S
• The time of day will be in 12-hour AM, 12-hour PM format.
Midnight will be displayed as 12:00am.
• Day/Time Setup:
• Press and hold the MODE Zone or the MODE/SET Button
for 5 seconds to enter Day/Time Setup.
• Press the UP or DOWN Buttons to adjust the day of week
(press the MODE/SET Button or wait for 15 seconds for ad-
justment to be accepted, then enter hour of day adjustment).
• Press the UP or DOWN Buttons to adjust the hour of the
day. The time will advance in 1-hour increments; AM and
PM will change when the hour advances to 12:00 midnight
and 12:00 noon respectively (press the MODE/SET Button
or wait for 15 seconds for adjustment to be accepted, then
enter minute of hour adjustment).
• Press the UP or DOWN Buttons to adjust the minute of the
hour. The time will advance in 1-minute increments (press
the MODE/SET Button or wait for 15 seconds and the
transmitter will exit Day/Time Setup and return to normal
operation).
• LCD Displays – when in Day/Time Setup:
