manualshive.com logo in svg
background image

126817-01F

4

SuperiorFireplaces.us.com

SAFETY

Continued

2.  Do not place propane/LP supply tank(s) inside 

any structure. Locate propane/LP supply 
tank(s) outdoors (propane/LP units only).

3.  If you smell gas

• shut off gas supply
• do not try to light any appliance
• do not touch any electrical switch; do not use 

any phone in your building

• immediately call your gas supplier from a 

neighbor’s phone. Follow the gas supplier’s 
instructions

• if you cannot reach your gas supplier, call the 

fi re department

4.  This heater shall not be installed in a bedroom 

or bathroom. This gas log set may not be 
installed as a vented appliance in a bedroom 
or bathroom in the Commonwealth of Mas-
sachusetts.

5. 

WARNING: Before installing in a solid 
fuel-burning fi replace, the chimney fl ue and 
fi rebox must be cleaned of soot, creosote, 
ashes and loose paint by a qualifi ed chimney 
cleaner

. Creosote will ignite if highly heated. 

A dirty chimney fl ue may create and distribute 
soot within the house. Inspect chimney fl ue for 
damage. If damaged, repair fl ue and fi rebox 
before operating appliance.

6.  Do not burn solid-fuel in a fi replace in which 

an unvented appliance is installed.

7.  If appliance has glass doors, never operate this 

appliance with glass doors closed. Any glass 
doors shall be fully opened when the appliance 
is in operation. If you operate appliance with 
doors closed, heat buildup inside fi replace will 
cause glass to burst. Make sure there are no 
obstructions across openings of fi replace.

8.  To prevent the creation of soot, follow the in-

structions in 

Cleaning and Maintenance

Page 

30

.

9.  Before using furniture polish, wax, carpet  

cleaner or similar products, turn appliance off. 
If heated, the vapors from these products may 
create a white powder residue within burner box 
or on adjacent walls and furniture.

10.  This appliance needs fresh, outside air ventila-

tion to run properly. This appliance has an 
Oxygen Depletion Sensing (ODS) safety shutoff 
system. 

1. WARNING: 

This appliance is only for use 

with the type of gas indicated on the rating 
plate. This appliance is not convertible for 
use with other gases. 

 

The ODS shuts down the appliance if enough 
fresh air is not available. See 

Air for Combus-

tion and Ventilation

Page 6

. If appliance keeps 

shutting off, see 

Troubleshooting

Page 31

.

11.  Do not run appliance

• where fl ammable liquids or vapors are used 

or stored

• under dusty conditions

12.  Do not use this appliance to cook food or burn 

paper or other objects.

13. Do not use this room heater if any part has 

been under water. Immediately call a qualifi ed 
service technician to inspect the room heater 
and to replace any part of the control system 
and any gas control which has been under 
water.

14.  Do not operate appliance if any log is broken. 

Do not operate appliance if a log is chipped 
(dime-sized or larger). 

15. Turn appliance off and let cool before servicing, 

installing or repairing. Make sure the selector 
switch is in the OFF position. Only a qualifi ed 
service person should install, service or repair 
appliance.

16. Make sure the selector switch is in the OFF 

position when you are away from home for 
long periods of time. 

17.  Remote-ready appliances must not be con-

nected to any external electrical source.

18.  Operating appliance above elevations of 4,500 

feet may cause pilot outage.

19. To prevent performance problems, do not 

use propane/LP fuel tank of less than 100 lb. 
capacity (propane/LP units only).

20.  Provide adequate clearances around air open-

ings.

21.  When installing as a vented appliance in a manu-

factured home or mobile home, the installation 
must conform with the Manufactured Home 
Construction and Safety Standard, Title 24 CFR, 
Part 3280, or when applicable, with Manufacture 
Home Installations Standard, ANSI/NCBCS 
A225.1/NFPZ 501A.

22.  This log heater is designed to be smokeless. If 

logs ever appear to smoke, turn off heater and 
call a qualifi ed service person. 

 

NOTE:

 

During initial operation, slight smoking 

could occur due to log curing and heater burning 
manufacturing residues.

Содержание LTFRS













































Отзывы: