Superiorfireplaces.US.com
126745-01D
4
UNPACKING
The following items are packed inside the firebox. Remove before
positioning firebox into framing.
• Ceramic Log Pack - Shrink wrapped on cardboard
• 3 plastic bags containing lava rock, pan and ember materials
• Rear Log (BRT2332TMN/BRT2532TMN Models Only). Remove 2
plastic quick ties from around burner and grate
• Grate Stand - Lift off of burner pan
Check all items for any shipping damage. If damaged, promptly
inform dealer or distributor where you bought the product.
Retain these items for later installation.
INTRODUCTION
These fireplace models are vented gas fireplaces that use a millivolt
gas control valve with a millivolt ignition system. 25" models have a
5" B-vent and 24" models have a 4" B-vent. A properly sized B-Type
venting system and listed type vent cap are not supplied but are
required for proper operation. See venting instructions on page 10.
WARNING: This gas appliance must not be con-
nected to a chimney flue servicing a solid fuel burning
appliance.
These models are factory equipped for use with natural gas and must
be converted when intended for use with propane/LP gas. Conver-
sion kits PCBM-324 and PCBM-325 may be purchased for simple
conversion to propane/LP gas. See Accessories, page 23.
BEFORE YOU BEGIN
Before beginning the installation of your appliance, read these in-
structions completely.
This INNOVATIVE HEARHT PRODUCTS (IHP) appliance and its ap-
proved components are safe when installed according to this instal-
lation manual and are operated as recommended by IHP. Using any
component fon IHP approved and tested for use with this appliance
MAY CAUSE A FIRE HAZARD!
The IHP warranty will be voided by, and IHP disclaims any respon-
sibility for the following actions:
A) Modification of the appliance or any of the components.
B) Use of any component part not approved by IHP in combination
with this appliance.
C) Installation and/or operation in a manner other than instructed
in this manual.
D) The burning of anything other than the type of gas approved for
use in this gas appliance.
Installation must conform with local codes or, in the absence of
local codes, with the current National Fuel Gas Code, ANSI Z223.1.
This fireplace complies with the National Safety Standards and is
listed and tested by PFS Corporation to ANSI Z21.50/CSA 2.22
standard as vented gas fireplace.
NOTICE: Decorative product not for use as a heating
appliance.
WARNING: Installation of this appliance should be
done by a qualified service person well trained in the
installation of such appliances. You will also need a
building permit from your local Building and Safety
Commissioner before installing this appliance; other-
wise your insurance co. may not cover this appliance.
CAUTION: Do not connect appliance before pressure
testing gas piping. Damage to gas valve may result
and an unsafe condition may be caused.
WARNING:
Young children should be carefully supervised when
they are in the same room as the appliance. Toddlers, young chil-
dren, and others may be susceptible to accidental burns. A physical
barrier is recommended if there are to be at-risk individuals in the
house. To restrict access to a fireplace or stove, install an adjust-
able safety gate to keep toddlers, young children, and other at-risk
individuals out of and away from hot surfaces.
The appliance and it’s individual shutoff valve must be disconnected
from the gas supply piping system during any pressure testing of
that system at test pressures in excess of 1/2 psig (3.5 kPa).
The appliance must be isolated from the gas supply piping system
by closing its individual manual shutoff valve during any pressure
testing of the gas supply piping system at test pressures equal to or
less than 1/2 psig (3.5 kPa).
For the purpose of input adjustment two pressure taps (for IN and
OUT pressures) are provided on the gas control valve for test gauge
connections to the appliance.
This fireplace may not be installed in manufactured (mobile) hous-
ing constructed to HUD standards. The fireplace may be installed in
aftermarket, non-HUD manufactured housing provided its installation
complies with State and Local Codes and in the absence of these
codes complies with the National Fuel Gas Code ANSIZ223.1 NFPA 54..
