SuperFlow SF- 902S Скачать руководство пользователя страница 35

Страница: 35 / 79

4.8 Computer System

Communication

The computer communicates with the sensor

system through an Ethernet Local Area Network

(LAN) cable. Connect the Category 5 (Cat-5)

network cable from the computer network switch

to the RJ-45 connector located on the side of the

sensor box labeled Computer Network.

SuperFlow WinDyn 4.0 systems use TCP/IP

network protocol. WinDyn 3.2.R2 uses NetBEUI

protocol.

Software

SuperFlow provides a USB thumb-drive containing the WinDyn software. The WinDyn software was

installed and configured on your computer system by factory personnel. The thumb-drive is only

necessary if you must recover or reinstall the Windyn software. Windyn software is also installed in a

SuperFlow System Recovery folder on the computers hard drive, along with manuals and other pertinent

documentation.

4.9 System Cable Connections

Open the sensor box. Verify all cables are firmly seated and connected. Close the box, lock it, and put the

keys in a safe place.

NOTE:

The power supply used in the sensor box and the console is 12 volt switching power supply.

Voltage checkpoints for both power supplies are provided on labels affixed to their case. Both use

universal input power supplies 100 - 240 VAC.

NOTE:

All system cables and their connection ports on the sensor box are labled. The cables are labeled

on each end to match the connection port they are to be connected to.

Power

Plug the computer and sensor box power

cables into a convenient outlet. The power

connection for the sensor box is on the bottom.

SuperFlow recommends plugging both units into

a suitable surge suppression circuit and using an

Uninterruptible Power Supply (UPS) or other power

backup for power outages.

Refer to "Electrical

Requirements" on page 12. There is a 2 amp

fuse for current overload protection in the power plug receptacle on the sensor box.

Figure 4.7 Network Router

Always turn the power off to

the system when plugging or

unplugging devices into the sensor

box and console.

WARNING

4.0 Installation

Содержание SF- 902S
















































































Результаты поиска

Содержание SF- 902S

Отзывы:

Похожие инструкции для SF- 902S

Бренды по названию

Популярные бренды

SuperFlow SF- 902S, Оригинальное руководство пользователя

Результаты поиска

Содержание SF- 902S

Отзывы:

Похожие инструкции для SF- 902S

Бренды по названию

Популярные бренды