SuperFlow SF- 902S Скачать руководство пользователя страница 16

Страница: 16 / 79

The Computer System

The computer system consists of a standard

computer with up to three monitors installed,

a color printer, and WinDyn dynamometer

software. Other than the network connection and

minimum performance specifications, no special

requirements must be met.

SuperFlow’s WinDyn dynamometer software

was designed for Microsoft

Windows

-based

computers.

The computer communicates with the sensor

system through an Ethernet Local Area Network

(LAN) cable. Commands to the test system can

only be issued from this computer.

All printers supported by Windows can be used.

A color printer is recommended for highest impact

and clarity of test graphs. The printer is connected

to the computer.

Electrical Requirements

The WinDyn instrumentation system requires a dedicated, stable electrical power source for proper

operation. SuperFlow recommends using an Uninterruptible Power Supply (UPS) that has a minimum

rating of 750 VA or a high-quality surge suppressor for the sensor box and computer. This may protect the

electronics from damage in the event of a power surge and keep the engine running if the power goes out.

It is best to connect all instrumentation devices to the same circuit to minimize ground loop noise. Adding

devices such as battery chargers and fan motors to the same circuit can cause noise problems.

The total power requirement for a basic instrumentation system is 120V/15A or 240V/8A.

TIP:

Your electrician can wire the electrical circuits in your test cell with outlets for the sensor box and

computer wired to a special protected circuit.

Figure 3.3: Operator Console

SuperFlow recommends dedicating the computer

connected to the dynamometer for dynamometer

use only and not utilizing it for other purposes.

Multiple programs and Internet access could

possibly slow down the computer and affect the

dynamometer operation.

IMPORTANT

3.0 System Overview

Содержание SF- 902S
















































































Результаты поиска

Содержание SF- 902S

Отзывы:

Похожие инструкции для SF- 902S

Бренды по названию

Популярные бренды

SuperFlow SF- 902S, Оригинальное руководство пользователя

Результаты поиска

Содержание SF- 902S

Отзывы:

Похожие инструкции для SF- 902S

Бренды по названию

Популярные бренды