Super SC809LT-780B Скачать руководство пользователя | Manualshive

Страница: 55 / 60

background image

C-5

Appendix C: SAS-809T/TQ Backplane Specifications

8. Upgrade Connectors

The upgrade connector, designated JP46, is
only included on the SAS-809TQ backplane
and is used for manufacturer's diagnostic
purposes only.

9. MG9071 Chip Reset

The  chip  reset,  designated  JP35,  is  only
included  on  the  SAS-809TQ  backplane
and is used to reset the MG9071 chip. For
details,  see  the  jumper  settings  section  of
this manual.

11. Buzzer Reset

The buzzer reset is designated as JP18. It
is used to reset the buzzer after it has been
activated.

12. MG9071 Chip

The MG9071 chip, is only included on the
SAS-809TQ backplane. It is an enclosure
management chip that supports the SES-2
controller and SES-2 protocols.

10. Mode Select

Mode select, designated JP33, is only included
on  the  SAS-809TQ  backplane.  It  allows
switching between I2C and SGPIO modes.
For  details, see the I2C and SGPIO settings
section of this manual.

«
...
53
54
55
56
57
...
»

Содержание SC809LT-780B





























































Отзывы:

Нет отзывов

Похожие инструкции для SC809LT-780B

Бренд: Lantronix Страницы: 10

Бренд: Lantronix Страницы: 17

Бренд: Lantronix Страницы: 109

Бренд: Lantronix Страницы: 24

Бренд: Lantronix Страницы: 29

Бренд: Lantronix Страницы: 2

Бренд: Zenith Страницы: 218

AirLive WP-203G

Бренд: Ovislink Страницы: 132

Transport TX46 (B4985) Service

Бренд: TYAN Страницы: 75

Бренд: AXIOMTEK Страницы: 58

TERASTATION HS-D1.0TGL/R5

Бренд: Buffalo Страницы: 2

Бренд: IBM Страницы: 75

Бренд: Moxa Technologies Страницы: 100

Бренд: IBM Страницы: 90

Бренд: myTEM Страницы: 2

Бренд: Planet Страницы: 83

Бренд: Promise Technology Страницы: 324

Бренд: Black Box Страницы: 46

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды