Super SC809LT-780B Скачать руководство пользователя | Manualshive

Страница: 37 / 60

background image

6-1

Chapter 6: Rack Installation

Chapter 6

Rack Installation

6-1 Overview

This chapter provides a quick setup checklist to get your chassis up and running.
Following these steps in the order given should enable you to have the system
operational within a minimum amount of time.

6-2 Unpacking the System

You should inspect the box the chassis was shipped in and note if it was damaged

in any way. If the chassis itself shows damage you should file a damage claim with

the carrier who delivered it.
Decide on a suitable location for the rack unit that will hold your chassis. It should
be situated in a clean, dust-free area that is well ventilated. Avoid areas where

heat, electrical noise and electromagnetic fields are generated. You will also need

it placed near a grounded power outlet. Be sure to read the Rack and Server Pre-
cautions in the next section.

6-3 Preparing for Setup

The box your chassis was shipped in should include two sets of rail assemblies,
two rail mounting brackets and the mounting screws you will need to install the
system into the rack. Please read this section in its entirety before you begin the
installation procedure outlined in the sections that follow.

Choosing a Setup Location

Leave enough clearance in front of the rack to enable you to open the front

•

door completely (25 inches).

Leave approximately 30 inches of clearance in the back of the rack to allow for

•

sufficient airflow and ease in servicing.

This product is for installation only in a Restricted Access Location (dedicated

•

equipment rooms, service closets and similar environments).

«
...
35
36
37
38
39
...
»

Содержание SC809LT-780B





























































Отзывы:

Нет отзывов

Похожие инструкции для SC809LT-780B

Univerge SV8100

Бренд: NEC Страницы: 2

Бренд: IBM Страницы: 908

Бренд: Synology Страницы: 15

ioLogik W5300 Series

Бренд: Moxa Technologies Страницы: 177

Бренд: TYAN Страницы: 77

Бренд: TYANO Страницы: 102

Бренд: IBM Страницы: 48

@server xSeries 343

Бренд: IBM Страницы: 193

Бренд: King Pigeon Страницы: 19

Бренд: NEC Страницы: 10

Бренд: NEC Страницы: 20

Бренд: NEC Страницы: 2

Бренд: NEC Страницы: 18

Бренд: NEC Страницы: 2

Care Standard/300

Бренд: NEC Страницы: 11

Бренд: NEC Страницы: 88

Бренд: NEC Страницы: 89

Бренд: NEC Страницы: 62

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды