background image

8

Recharge discharged batteries as soon as possible after use or battery life may be greatly 

diminished. For longest battery life, do not discharge batteries fully.It is recommended that the 

batteries be recharged after each use.

IMPORTANT CHARGING NOTES 

1. Your tool was sent from the factory in an uncharged condition. Before attempting to use it, it 

must be charged.

2. CAUTION: To reduce the risk of damage to the batteries, NEVER charge them in an air 

temperature below 40°F (4.5°C) or above 105°F (40.5°C). Also, NEVER charge them if the 

battery temperature is below 40°F (4.5°C) or above 105°F (40.5°C). Longest life and best 

performance occur when batteries are charged with an air temperature of approximately 

75°F (24°C). NOTE: The tool will not charge if the tool temperature is below approximately 

32°F (0°C) or above 113°F (45°C). 

3. While charging, the charger may hum and become warm to touch. This is a normal 

phenomenon and does not indicate a problem. 

4. If the batteries do not charge properly --(1) Check current at receptacle by plugging in a lamp 

or other appliance. (2) Check to see if receptacle is connected to a light switch which turns 

power off when you turn out the lights. (3) Move charger and tool to a surrounding air 

temperature of 40°F (4.5°C) to 105°F (+40.5°C). (4) If the receptacle and temperature are 

OK, and you do not get proper charging, take or send the tool and charger to us. 

5. The tool should be recharged when it fails to produce sufficient power on jobs which were 

easily done previously. Battery life may be greatly diminished if batteries are discharged 

deeply. DO NOT CONTINUE using product with its batteries in a depleted condition. 

Recharge discharged batteries promptly. 

6. To maximize battery life: 

a. Do not fully discharge batteries. 

b. Fully recharge batteries after each use. 

c. Store tool in a location where the surrounding air temperature is approximately 40°F-75°F 

(4.5°C - 24°C). 

d. Disconnect charger from tool after charge is complete. 

Fire Hazard. When disconnecting the charger from the tool, be sure to unplug the charger from 

the outlet first, then disconnect the charger cord from the tool. 

FIRE HAZARD. When remove the batteries from the charger, be sure to unplug the

charger from the outlet first, then remove the batteries from the charger.

Charger plug     Charging hole    Power light

Содержание GUT099





















Отзывы: