manualshive.com logo in svg

SUNWARD SWE25UF, Руководство по эксплуатации и техническому обслуживанию

Поделиться
Скачать
SUNWARD SWE25UF Скачать руководство пользователя страница 52

 

47 

 

5)

 

Mark hand rigging on the load to ensure the people pulling hand rigging is away from load. 

6)

 

Try to lift the load before normal operation.   

⚫

 

Park the machine beside the load. 

⚫

 

Load the machine.   

⚫

 

Lift load to the height of 50mm (2in) off the ground.   

⚫

 

While keeping the load close to ground, move the load from the machine. 

⚫

 

If there is any evidence of stability reduction, lower load to the ground.   

7)

 

Just lift the load to required height. 

 

3.7 HYDRAULIC BREAKING OPERATION   

Hydraulic breaking operation tips…if equipped

   

Choose hydraulic breaker with correct dimension and weight. Consult with your dealer. 

Pump / Main valve section assignment 

The hydraulic pressure of section AUX (the hydraulic pressure of the breaker section) supplied 

by P2 is 21 M Pa. 

Attention to hydraulic breaker tubing

 

1)

 

When the hydraulic breaker is out of use, cover the 

pipe  end  of  arm  and  fit  a  plug  at  the  end  of 

hydraulic  breaker  hose  to  avoid  dirt  entering  into 

system. 

2)

 

Ensure 

stocking 

cover 

and 

plug 

in 

tool 

compartment for maintenance purpose. 

3)

 

Avoid dirt entering into system when change bucket with breaker. 

4)

 

After connection, check the oil leakage and bolts slack condition. 

Before  fitting  hydraulic  breaker  on  the  arm,  read 

machine and hydraulic breaker manuals carefully, and 

carry out the required confirmation or inspection. 

Carry  out  required  inspection  before  daily 

operation. 

1)

 

Operate  machine  slowly,  the  stability  of  machine 

will be decreased because the hydraulic breaker is 

heavier  than  the  bucket.  Therefore,  use  dozer 

blade to support and work in front of dozer blade. 

FIG. 3-38 

 

FIG. 3-39 

 

Содержание SWE25UF











































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды