background image

-4- 

 

SAFETY INFORMATION FOR USERS OF LP-GAS 

 
Propane (LP-Gas) is a flammable gas that can cause fires 
and  explosions.    In  its  natural  state,  propane  is  odorless 
and colorless.  You may  not know all the following safety 
precautions,  which  can  protect  both  you  and  your  family 
from  an  accident.    Read  them  carefully  now,  then  review 
them point by point with the members of your household. 

Someday  when  there  may  not  be  a  minute  to  lose, 
everyone's safety will depend on knowing exactly what to 
do. If, after reading the following information, you feel you 
still  need  more  information,  please  contact  your  gas 
supplier.

 

LP-GAS WARNING ODOR 

 

If a gas leak happens, you should be able to smell the gas because of the odorant put in the LP-Gas. 

That's your signal to go into immediate action! 

 

!

  Do  not  operate  electric  switches,  light  matches,  or  use  your 

telephone.  Do not do anything that could ignite the gas. 

!

  Get everyone out of the building, vehicle, trailer or area.  Do 

that 

IMMEDIATELY.

 

!

  Close all gas tank or cylinder supply valves. 

!

  LP-Gas is heavier than air and may settle in low areas such as 

basements.    When  you  have  reason  to  suspect  a  gas  leak, 
keep  out  of  basements  and  other  low  areas.    Stay  out  until 
firefighters declare them safe. 

!

  Use  your  neighbor's  telephone  and  call  a  trained  LP-Gas 

service  person  and  the  fire  department.    Even  though  you 
may not continue to smell gas, do not turn on the gas again.  
Do not re-enter the building, vehicle, trailer or area. 

!

  Finally, let the service man and firefighters check for escaped 

gas.  Have them air out the area before you return.  Properly 
trained  LP-Gas  service  people  should  repair  the  leak,  then 
check and relight the gas appliance for you. 

 

NO ODOR DETECTED - ODOR FADE 

 

Some people cannot smell well.  Some people cannot smell the 
odor of the chemical stench put into the gas.  You must find out if 
you  can  smell  the  odorant  in  propane.    Smoking  can  decrease 
your ability to smell.  Being around an odor for a time can affect 
your  sensitivity  or  ability  to  detect  that  odor.    Sometimes  other 
odors in the area mask the gas odor.  People may not smell the 
gas odor or their minds are on something else.   Thinking  about 
smelling a gas odor can make it easier to smell. 

 

The  odorant  in  LP-Gas  is  colorless,  and  it  can  fade  under  some 
circumstances.  For example, if there is an underground leak, the 
movement of the gas through soil can filter the odorant. 
 

Odorants in LP-Gas also are subject to oxidation.  Odor fading can 
occur if there is rust inside the storage tank or in iron gas pipes. 

 

The  odorant  in  escaped  gas  can  adsorb  or  absorb  onto  or  into 
walls, masonry and other materials and fabrics in a room.  That 
will  take  some  of  the  odorant  out  of  the  gas,  reducing  its  odor 
intensity. 

 

LP-Gas may stratify in a closed area, and the odor intensity could 
vary at different levels.  Since it is heavier than air, there may be 
more  odor  at  lower  levels.    Always  be  sensitive  to  the  slightest 
gas  odor.    If  you  detect  any  odor,  treat  it  as  a  serious  leak.  
Immediately go into action as instructed above. 

SOME POINTS TO REMEMBER 

 



Learn  to  recognize  the  odor  of  LP-Gas.    Your  local  LP-Gas 
Dealer can give you a "Scratch and Sniff" pamphlet.  Use it 
to find out what the propane odor smells like.  If you suspect 
that your LP-Gas has a weak or abnormal odor, call your LP-
Gas Dealer. 

 

If  you  are  not  qualified,  do  not  light  pilot  lights,  perform 
service,  or  make  adjustments  to  appliances  on  the  LP-Gas 
system.    If  you  are  qualified,  consciously  think  about  the 
odor  of  LP-Gas  prior  to  and  while  lighting  pilot  lights  or 
performing service of making adjustments. 

 

Sometimes  a  basement  or  a  closed-up  house  has  a  musty 
smell that can cover up the LP-Gas odor.  Do not try to light 
pilot  lights  in  the  area  where  the  conditions  are  such  that 
you may not detect the odor if there has been a leak of LP-
Gas. 

 

Odor fade, due to oxidation by rust or absorption on walls of 
new  cylinders  and  tanks,  is  possible.    Therefore,  people 
should  be  particularly  alert  and  careful  when  new  tanks  or 
cylinders are placed in service.  Odor fade can occur in new 
tanks, or reinstalled old tanks, if they are filled and allowed 
to sit too long before refilling.  Cylinders and tanks that have 
been  out  of  service  for  a  time  may  develop  internal  rust, 
which will cause odor fade.  If such conditions are suspected 
to  exist, a periodic sniff test of the gas is advisable.  If you 
have  any  question  about  the  gas  odor,  call  your  LP-Gas 
dealer.   A  periodic sniff test of the LP-Gas  is a good safety 

measure under any condition. 

 

If, at any time, you do not smell the LP-Gas odorant and you 
think  you  should,  assume  you  have  a  leak.    Then  take  the 
same  immediate  action  recommended  above  for  the 
occasion when you do detect the odorized LP-Gas. 

 

If  you  experience  a  complete  "gas  out"  (the  container  is 
under  no  vapor  pressure),  turn  the  tank  valve  off 
immediately.  If the container valve is left on, the container 
may  draw  in  some  air  through  openings  such  as  pilot  light 
orifices.    If  this  occurs,  some  new  internal  rusting  could 
occur.  If the valve is left open, then treat the container as a 
new  tank.    Always  be  sure  your  container  is  under  vapor 
pressure  by  turning  it  off  at  the  container  before  it  goes 
completely empty or having it refilled before it is completely 
empty. 

Содержание SC10M-1-LP

















Отзывы: