SunStar KM-570BL Скачать руководство пользователя страница 11

Страница: 11 / 29

7) Installation of thread stand

As shown in

“

Figure 7

”

, assemble the thread stand

①

insert it in the table hole, and use the fixed nut

②

and

washer

③

to fix it.

[Figure 7]

6) Installation of belt cover

A. Set the groove at the bottom of belt cover

“

”①

to be

aligned with the groove of the head of the belt cover

supporting screw

②

, and insert the cover into the groove.

Use the belt cover fixing screws

③

(2EA) to fix the

cover to the body of the machine.

B. Insert the belt cover

“

”②

into the belt cover

“

”①

while maintaining the balance. Use the belt cover fixing

screws (3EA) to fix the belt covers to the body of the

machine.

[Figure 6]

5) Installation of program unit (Trimmer Type)

A. Use 4 fixed screws

③

to fix the bracket

②

on the

program unit

①

B. In the program unit

①

, use two fixed bolts

④

to tightly

fix the assembled brackets

②

[Figure 5]

③

①

②

④

①

②

③

④

①

②

③

Содержание KM-570BL






























Результаты поиска

Содержание KM-570BL

Отзывы:

Похожие инструкции для KM-570BL

Бренды по названию

Популярные бренды

SunStar KM-570BL, Руководство пользователя

Результаты поиска

Содержание KM-570BL

Отзывы:

Похожие инструкции для KM-570BL

Бренды по названию

Популярные бренды