manualshive.com logo in svg

SunStar KM-1060BL, Руководство пользователя

Поделиться
Скачать
SunStar KM-1060BL Скачать руководство пользователя страница 5

5

1-1) Machine mobilization

Danger

1-2) Machine installation

Caution

1-3) Troubleshooting

Danger

When the machine is in need of repair, only our authorized service technicians must
handle it.

ⓐ Before  cleaning  and  repairing  the  machine,  shut  off  the  power  supply  and  wait  four

minutes for the machine to discharge completely.  

ⓑ No  part  of  the  machine  or  specifications  may  be  modified  without  prior  consultation

with our company.  Any such modification could risk safe operation of the machine.

ⓒ In case of repair, replace only with standard OEM parts from SunStar.
ⓓ After repair, put safety covers back on the machine.

Only personnel with a full understanding of the safety rules should move the machines.
The following directions must be observed when delivering the machines.

ⓐ At least two or more people should move the machine.
ⓑ Before delivering the machine, thoroughly wipe off the oil on the machine to prevent

accidents.  

Physical damages such as functional difficulties or breakdowns may occur depending on
installation conditions of the machines.  Be sure to heed the following conditions.

ⓐ Remove the packing from top to bottom.  Watch out for nails on the wooden box. 
ⓑ Install a climate controller and clean it regularly to prevent dust and moisture build-

up from contaminating and corroding the machines.

ⓒ Keep the machines away from direct sunlight. 
ⓓ Keep a minimum distance of 50cm between the machine at both sides and backside

and the wall to secure sufficient space for repair.

ⓔ Risk of explosion

Do not operate the machine near areas with danger of explosion.  Refrain from running
the machine in the vicinity of risky places e.g., where a large quantity of aerosol-
spraying products or oxygen are handled, unless specific guarantees are given otherwise
for the operation of the machine to prevent explosion at such places.

ⓕ The user should install an illuminator in the work area for the machine does not come

supplied with any lighting apparatus due to the specific features of the machine. 

[Note] Details of the machine installation are laid out in No. 2 Installation.

Содержание KM-1060BL









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды