Sunrise Medical E1161 Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 28

background image

Zippie

®

SPHYNX

252843 Rev. B

23

9.0 DEALER SERVICE AND ADJUSTMENT

9.17

Seat frame

Telescoping seat tube

Rear seat sling

9.18

Rear bolt

9.20

9.21

Screw

Rear seat

rail plug

9.24

9.25

Rear seat

rail plug

Rear seat

sling

Rear Seat Sling Tension Adjustment

1.

Remove seat cushion.

2.

Remove front seat sling by completing steps 2-4
from Front Seat Sling Adjustment (previous page).

3.

Remove telescoping seat tubes. (Fig 9.17)

4.

Remove rear bolts and nuts from outer seat rail.
(Fig 9.18)

5.

Insert the short end of a 6mm allen wrench into
the channel of the rear seat rail plug and rotate plug
inward so that the channel faces up. Complete on
both sides of chair. (Fig 9.19)

6.

Remove rear seat sling and rear seat sling rods.

7.

Adjust tension by adjusting Velcro

®

foldover on

sling.

8.

Replace rear seat sling and seat sling rods
positioning as far back as possible, until rear seat
sling bottoms out on ﬂ athead screw and rear seat
rail plug bottoms out at backstop. (Fig 9.20,
Fig 9.21, Fig 9.22, Fig 9.23)

9.

Tighten back edge of rear seat sling:
a. Make sure the backrest is in the most

forward recline setting (85°) to make rear

bolt hole accessible.

b. Insert the short end of a 6mm or 1/4” allen

wrench L-Key (or similar sized tool with

90° bend) into the exposed channel of

rear seat rail plug and rotate rear plug 90°

outward until its bolt hole is aligned with

the hole in the outer seat rail and rear

plastic covers (Figures 9.24 & 9.25).

c.

With the holes aligned, insert bolt as shown in

Fig 9.18. Do the same to the other side which

should pull the rear end of the rear seat sling

taut and insert the bolt while holding the sling

taut, making sure the holes are aligned.

Note: If the rear end of the seat sling is not taut,
remove the seat sling and adjust the width of the
sling with the Velcro

®

adjustment. When the rear

seat sling assembly is properly attached with the
desired tension, fasten nuts on to the bolts.
(Fig 9.18)

10. Insert telescoping seat tubes to appropriate seat

depth setting. Mark on side frame should align with
mark on telescoping seat tube. (Fig 9.26)

11. Insert front seat sling and seat sling rods.
12. Turn telescoping seat tube outward to align holes

and insert bolts on both sides of chair and fasten
with nuts. Torque each of the two nuts to
16.3 Nm [144 in-lbs] with a 10mm torque
wrench while securing bolts with a standard
4mm Allen.

Do not attempt to use a 4mm

Allen head torque wrench as this will likely
damage the hex socket portion of the bolt
head.

13. Attach seat rail end caps by starting with slot in end

cap inserted into seat sling. Then, rotate outward
so that channel in cap is facing up. Push end cap
until it bottoms out on telescoping seat tube.
(Fig 9.27 & Fig 9.28)

9.27

Seat rail end cap

9.22

9.23

Rear seat

rail rods

Seat frame

Rear seat

sling

Rear

plug

Seat frame

Backstop

9.26

Telescoping

seat tube

0

15

15

30

30

45

TORQUE !

Seat depth

indicator

marks

9.19

Backstop

9.28

9.17

9.18

9.19

9.20

9.21

9.22

9.23

9.24

9.25

9.26

9.27

9.28

Rear seat

rail plug

Channel facing up

Seat frame

«
...
21
22
23
24
25
...
»

Содержание E1161





























Отзывы:

Нет отзывов

Похожие инструкции для E1161

Бренд: Invacare Страницы: 40

Бренд: decon Страницы: 41

Бренд: Croydex Страницы: 2

Бренд: Quickie Страницы: 44

Бренд: R82 Страницы: 42

Бренд: WOK Страницы: 34

Бренд: R82 Страницы: 178

Бренд: Power Stand Страницы: 24

Бренд: Vermeiren Страницы: 200

Бренд: DELTA-SPORT Страницы: 26

Бренд: Safer Locks Страницы: 25

Solstice Comfort

Бренд: Days Страницы: 144

Бренд: panthera Страницы: 5

Бренд: panthera Страницы: 22

Бренд: panthera Страницы: 24

U3 Light Y-Front

Бренд: panthera Страницы: 24

Бренд: panthera Страницы: 25

Бренд: Zippie Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды