5)
Note: here device type is selected as DIM as an example, please select your correct DALI device type.
Select the DALI Address to be Controlled Using Dial Switches 1-6
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8 9 10
9 10
Controlled address
Controlled address
00
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
Note: 1)
once DALI device type and address control mode are selected, please then select the DALI address
2)
.
(00-63 selectable) to be controlled on DALI line by dial switches.
The control gear with the selected DALI address on DALI line will be controlled
6) o wiring after above all settings are completed according to wiring diagram.
D
1 2 3 4 5 6 7 8 9 10
Dial up
Dial down
7) Pair/delete the pairing with RF+Bluetooth remote
8) Pair with smart APP
1. Do wiring according to connection diagram.
2. Please refer to the
EasyThings
App user manual for details of adding device.
0/1-10V Dimmable
Driver
ACL
ACN
DIM+
DIM-
LED+
LED-
Wiring Diagram
When 0/1-10V Output Selected
L
N
M
a
x
. 5
A
R
e
la
y
LED+ V+
LED- V-
LED light
DA/-
DA/+
Prog.
Input Voltage: 110-240V AC
Output Current: 1x5A max
SR-BUS to DALI+0/1-10V
2 in 1 Converter with Relay
D
A
L
I
0
/1
-1
0
V
DALI Add.
ta:-20
℃
-+50
℃
1
5
3
7
9
2
6
4
8
10
L
L1
N
N
Note
: 1) Max. 50mA DALI bus PS output to supply control current to up to 25 control gears.
2) The max. load of the relay is 5A, and the number of control gear can be switched by the
relay depends on the load of each control gear.
DALI Bus
When DALI Output Selected
L
N
M
a
x
. 5
A
R
e
la
y
DA
DA
DALI DT6/DT8 Control Gear
L
N
DA
DA
DALI DT6/DT8 Control Gear
L
N
LED+
LED-
LED+
LED-
LED+ V+
LED- V-
LED+ V+
LED- V-
LED light
LED light
DA/-
DA/+
Prog.
Input Voltage: 110-240V AC
Output Current: 1x5A max
SR-BUS to DALI+0/1-10V
2 in 1 Converter with Relay
D
A
L
I
0
/1
-1
0
V
DALI Add.
ta:-20
℃
-+50
℃
1
5
3
7
9
2
6
4
8
10
L
L1
N
N
1. Do wiring according to connection diagram.
2. Pair LED controller with RF+Bluetooth remote: please refer to the instruction of the remote that you would
like to pair with.
3. Delete the pairing:
(1) Wire up the LED controller correctly, power on.
(2) Press and hold down the
“Prog.”
button on the controller for over 3 seconds (or reset power of the device
8 times continuously if the button is not accessible to factory reset the device) until the connected light flashes,
which means well deleted.
Note: factory resetting will restore all configured parameters of the device on the APP to factory default setting.
