background image

Operation manual of solar water controller SR868C8/SR868C8Q 
 

--------------------------------------------------------------------------------------------------------------------------------------------------- 

- 8 - 

 
 
 

Port 3: connect black wire ( GND) 

Note

: please lead wire into indoors, and fix the cable outdoors. 

 

 

Sensor input ports   

Input sensor ports T0, T1: for Pt1000 sensors, used for measuring the temperature of 

collector and measuring the heat output. 

Input sensor ports T2, T3, and T4: for NTC10K, B=3950 sensors, used for measuring 

the temperature of tank and pipe.     

 

 

Advice regarding the installation of temperature sensors: 

 

 

Only original factory equipped Pt1000 temperature sensors are approved for use with 
the  collector,  it  is  equipped  with  1.5meter  silicon  cable  and  suitable  for  all  weather 
conditions,  the  temperature  sensor  and  cable  are  temperature  resistant  up  to  280

not necessary to distinguish the positive and negative polarity of the sensor connection.   
 
Only original factory equipped NTC10K,B=3950 temperature sensors are approved for 
use  with  tank  and  pipe,  it  is  equipped  with  1.5meter  PVC  cable,  and  they  are 
temperature  resistant  up  to  105

,  not  necessary  to  distinguish  the  positive  and 

negative polarity of the sensor connection.   
 
All  sensor  cables  carry  low  voltage,  and  to  avoid  inductive  effects,  must  not  be  laid 
close to 230 volt or 400-volt cables (minimum separation of 100mm)   
 
 
If external inductive effects are existed, e.g. from heavy current cables, overhead train 
cables,  transformer substations,  radio  and  television  devices,  amateur  radio  stations, 
microwave devices etc, then the cables to the sensors must be adequately shielded.   
 
Sensor cables may be extended to a maximum length of ca. 100 meter, when cable’s 

length is up to 50m, and then 0.75mm

cable should be used. When cable’s length is up 

to 100m, and then 1.5mm

cable should be used.   

 

 

Output ports 

Output P1

For solar circuit pump, semiconductor relay (SCR relay), also suitable for 

RMP control, max. switching current 1A, 

Output  P2

for  hot  water  circuit  pump,  electromagnetic  relay,  and  max.  switching 

current 3.5A,   

P2

 ports are always open,   

Output  R1

for  by-pass  circuit  pump  or valve,  electromagnetic  relay,  max. switching 

current 3.5A, R1 ports are always open,   

Содержание SR868C8













































Отзывы: