SUNFLOWER SR868C8 Скачать руководство пользователя

Страница: 37 / 44

Operation manual of solar water controller SR868C8/SR868C8Q

---------------------------------------------------------------------------------------------------------------------------------------------------

- 36 -

4.12 Manual heating

Description:

Electrical heater, gas or oil boiler can be as back-up devices in a solar system, this

controller can achieve constant temperature controlling, when controller gets

temperature signal of top part tank (T3) is 2

℃

below the preset temperature, back-up

heating will be triggered. When temperature of top part tank (T3) reaches to the preset

temperature, heating is ceased.

Conditions for triggering manual heating function: the setting temperature should be

℃

higher than tank temperature.

Activate/deactivate the function:

►Press “Heating” button, temperature “60

℃

” blinks on the screen.

►Press “+”“-” button to adjust switch-on temperature, adjustable range 10

℃～

℃

factory set is 60

℃

After 20 seconds, this function is activated, signal displays on the screen, and

heating signal blinks also.
►Press “Heating” button again, to switch-off manual heating function.

Note:

manual heating can only heat tank one time, after manual heating is triggered,

when temperature of tank rises up to the preset temperature, manual heating ceases,

and manual heating function will be deactivated automatically, if customer wants to

heat again, you need redo according to above steps.

4.13 Temperature query function

Under standby status,
►Press “+”“-” button can check the value of temperature sensors T0~ T4, pump speed

(

ｎ％

), accumulative operation time of circuit pump (Hp), daily thermal energy (DKWH),

accumulative thermal energy (KWH) or (MWH).

When checking temperature, T0

– T4 will displays one by one, corresponding sensor

signal blinks.
►Press “ESC” button,

clock

and tank temperature can be displayed.

Note:



Value of accumulative operation time of circuit pump (Hp), daily thermal energy

Содержание SR868C8













































Результаты поиска

Содержание SR868C8

Отзывы:

Похожие инструкции для SR868C8

Бренды по названию

Популярные бренды

SUNFLOWER SR868C8, Инструкция по установке и эксплуатации

Результаты поиска

Содержание SR868C8

Отзывы:

Похожие инструкции для SR868C8

Бренды по названию

Популярные бренды