manualshive.com logo in svg

Sunco Gardner Denver Sutorbilt Legend GAA P Series, Список запасных частей и руководство по эксплуатации и обслуживанию

Поделиться
Скачать
Sunco Gardner Denver Sutorbilt Legend GAA P Series Скачать руководство пользователя страница 5

SB--7--621

Page iv

SAFETY PRECAUTIONS

Safety is everybody’s business and is based on your use of good common sense. All situations or circumstances
cannot always be predicted and covered by established rules. Therefore, use your past experience, watch out for
safety hazards and be cautious. Some general safety precautions are given below:

Failure to observe these notices could result in injury to or death of personnel.

D

Keep fingers and clothing away from blower inlet and discharge ports,
revolving belts, sheaves, drive coupling, etc.

D

Do not use the air discharge from this unit for breathing -- not suitable for
human consumption.

D

Do not loosen or remove the oil filler plug, drain plugs, covers, or break any
connections, etc., in the blower air or oil system until the unit is shut down
and the air pressure has been relieved.

D

Electrical shock can and may be fatal.

D

Blower unit must be grounded in accordance with the National Electrical
Code. A ground jumper equal to the size of the equipment ground conductor
must be used to connect the blower motor base to the unit base.

D

Open main disconnect switch, tag and lockout before working on the control.

D

Disconnect the blower unit from its power source, tag and lockout before
working on the unit -- the machine may be automatically controlled and may
start at any time.

Failure to observe these notices could result in damage to equipment.

D

Stop the unit if any repairs or adjustments on or around the blower are
required.

D

Disconnect the blower unit from its power source, tag and lockout before
working on the unit -- the machine may be automatically controlled and may
start at any time.

D

Do not exceed the rated maximum speed shown on the nameplate.

D

Do not operate unit if safety devices are not operating properly. Check
periodically. Never bypass safety devices.

Содержание Gardner Denver Sutorbilt Legend GAA P Series











































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды