Sun System RS 1850 LED, Инструкция по установке и эксплуатации

Страница: 2 / 13

2
2. PRODUCT DESCRIPTION:
The Sun System
®
RS 1850 LED is an electronic horticultural LED fixture. It drives six LED rails. The Sun System RS 1850 LED is intended to be used
in greenhouses or in climate rooms. In this manual, the Sun System RS 1850 LED will be referred to as: “the LED fixture”.
3. PRODUCT INFORMATION AND SPECIFICATIONS:
INPUT VOLTAGE : 120 - 277 V
INPUT POWER: 720 W
INPUT CURRENT : 2.62 A @ 277 V；6.2 A @ 120 V
HEAT LOAD : 2,450 btu/hr
FREQUENCY : 50/60 Hz
POWER FACTOR : > 0.95
AMBIENT TEMP : 131° F / 55° C
ENVIRONMENT RATING : IP65
MOUNTING : Hanger and safety wire
WEIGHT : 24.45 lb (12 kg)
DIMENSIONS : 1100 mm x 1000 mm 70 mm
CERTIFICATIONS : UL 1598, ANSI/CAN/UL 8800, and CSA C22.2 No. 250.0
WARRANTY : 5 year limited warranty
3.1 ENVIRONMENT:
The product is intended to be used in greenhouses and climate rooms. The product can be used in wet environments. The product may not be used
outdoors. A mechanical ventilation or cooling system is required to maintain the temperature within the growing space below 131° F / 55° C when the
Sun System RS 1850 LED is in operation.
LEGAL:
This device complies with Part 15 of the FCC Rules, designated as Class A. This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in
a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
This device has been designed to comply with the rules of the Federal Communications Commission. Changes or modifications not expressly approved
could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Conforms to ANSI/UL STD 1598, ANSI/CAN/UL 8800, and CSA C22.2 No. 250.0
4. SAFETY RECOMMENDATIONS AND WARNINGS:
Warning! Carefully read the warnings below before using or working with the product!

Always adhere to local rules and regulations when installing or using the LED fixture.

Do not open or disassemble the LED fixture; there are no serviceable parts inside. Opening or modifying the LED fixture can be dangerous and will
void the warranty.

This product may cause interference to radio equipment and should not be installed near maritime safety communications equipment or other
critical navigation or communication equipment operating between 0.45-30 MHz.

Do not use the LED fixture when either the LED fixture or its power cord are damaged. Replace the power cord only with original, certified cords.

Modifications to the cords can lead to unwanted electromagnetic effects, which makes the product not comply with legal requirements.

Do not expose the LED fixture to:
- (ambient) temperatures outside the specified range;
- dust and contamination;
- direct sunlight during use or HID light that could heat up the fixture.

Always disconnect the LED fixture from mains before performing any maintenance.

Always allow for a cool-down period of at least 30 minutes before touching the LED. Touching the LED when the fixture is lit or immediately
afterward can result in severe burns!

Do not use the LED fixture near flammable, explosive or reactive substances. Do not use sulfur vaporizers.

The installation and use of the LED fixture is the responsibility of the end user. Incorrect use or installation can lead to failure and damage to the
LED fixture. Damage to the LED fixture and electronic circuitry as a result of incorrect installation and use voids the warranty.

The minimum distance between adjacent lighting equipment is 4 inches (10.16 cm). The minimum distance between lighting equipment and
combustible materials is 4 inches (10.16 cm).