manualshive.com logo in svg

Sulzer ABS RCP 400, Инструкция по установке и эксплуатации, Страница: 6 / 42

Поделиться
Скачать
Sulzer ABS RCP 400 Скачать руководство пользователя страница 6

6

1.4.2 

Application areas RCP

The ABS submersible recirculation pumps RCP 400 and 500 are fitted with water-pressure-tight encapsulated 

motors and are quality products suitable for use in the following areas: 

• 

Pumping and recirculation of active sludge in treatment plants with nitrogen removal (nitrification/denitrifica

-

tion).

• 

Pumping of rain and surface water.

1.5 

Identification code

Motor power (P

2

 [kW/hp] x 10)

Number of poles in motor

Motor size

Motor

Material used

Ex version

  AA   BB C D    U VVV / W-XY Ex

EC; CR

Hydraulics

Motor designation (e.g. A)

Propeller Ø [cm] for RW

Discharge size DN [cm] for RCP

  

Propeller type*

Identity number

Series

0551-0003

*Propeller type: 1 = Mixing propeller (only without flow ring); 2 = 2-blade thrust propeller; 3 = 3-blade thrust propeller; 

 

  4 = 2-blade thrust propeller with flow ring; 5 = 3-blade thrust propeller with flow ring; 

 

  7 = 3- blade special propeller for biofilm carrier process

1.6 

Technical data

The maximum noise level of the units of this series is ≤ 70 dB(A). In some types of installation it is possible that 

the noise level of 70 dB(A) or the measured noise level will be exceeded.

ATTENTION 

The maximum fluid temperature for continuous operation is 40 °C / 104 °F for a 

submerged unit.

Содержание ABS RCP 400











































Отзывы:

Нет отзывов