manualshive.com logo in svg

Sulzer ABS RCP 400, Инструкция по установке и эксплуатации, Страница: 14 / 42

Поделиться
Скачать
Sulzer ABS RCP 400 Скачать руководство пользователя страница 14

14

2 Safety

The general and specific health and safety instructions are described in detail in the separate booklet 

Safety 

Instructions for Sulzer Products Type ABS

. If anything is not clear or you have any questions as to safety 

make certain to contact the manufacturer Sulzer. 

3 

Transport and storage

3.1 Transport

The unit must never be raised by the power cable.

Depending on the version, the units are fitted with a lifting hoop/eyelet, to which a chain can be fastened by 

means of shackles for transportation, installation or removal.

Take note of the entire weight of the unit (see nameplate Figure 2). The hoist and chain must be  

adequately dimensioned for the weight of the unit and must comply with the current valid safety  

regulations. Good technical practice must be observed.

T

he unit should be protected from rolling over!

The unit is prepared for transportation by placing it on an adequately strong, completely horizontal  

surface, taking care that it cannot topple over.

D

o not stay or work in the swivel area of a suspended load!

The lifting hook height must take into consideration the entire height of the unit as well as the length of 

the lifting chain.

3.2 

Transport securing devices

3.2.1 

Motor connection cable moisture protection

The motor connection cables are protected against the ingress of moisture along the cable by having the ends 

sealed at manufacture with protective covers.

ATTENTION 

These protective covers should only be removed immediately prior to connecting the 

pumps electrically.

Particular attention is necessary during storage or installation of units in locations, which could fill with water 

prior to laying and connection of the power cable of the motor. Please note that the cable ends, even where 

fitted with protective sleeves, must not be immersed in water. 

ATTENTION 

These protective covers only provide protection against water spray or similar and 

are not a watertight seal. The ends of the cables should not be immersed in water, 

otherwise moisture could enter the connection chamber of the motor.

NOTE 

If there is a possibility of water ingress then the cables should be secured so that the 

ends are above the maximum possible flood level. Take care not to damage the cable 

or its insulation when doing this!

Содержание ABS RCP 400











































Отзывы:

Нет отзывов