SUHNER ABRASIVE URG 9-R, Техническая документация

Страница: 20 / 60

1.1 g
enerAl notes on sAfety
This operation manual is applicable for the machine URG
9-R. The machine may only be handled by personnel who
are qualified.
Hold power tools by insulated gripping surfaces when
performing an operation where the cutting tool may con-
tact hidden wiring or its own cord. Contact with a «live»
wire will make exposed metal parts of the tool «live» and
shock the operator.
WARNING Read all safety warnings and all in-
structions.
Failure to follow the warnings and in-
structions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future refer-
ence.
1.2 u
se of the mAchine for purposes for
which it is intended
The machine is intended for the grinding and deburring
of metal with hard-metal milling cutters and plastic-resin
bonded forming abrasive wheels without the use of water.
The machine is designed exclusively for a 2-hand appli-
cation.
The machine is designed to drive the SUHNER extension
systems (VS).
1.3 i
ncorrect use
All uses other than those described under section
1.2 are regarded as incorrect use and are there-
fore not admissible.
1.4 ec
declArAtion of conformity
Otto Suhner GmbH of Trottäcker 50, D-79713 Bad Säck-
ingen, hereby declares under sole responsibility that the
product with the serial or batch no. (see reverse side) com-
plies with the requirements under the Directive 2014/30/
EU, 2006/42/EC, 2011/65/EU. Applied standards: EN ISO
12100, EN 60745, EN 55014-1, EN 55014-2, EN 61000-3-
2, EN 61000-3-3. Document Agent: M. Voyame. D-Bad
Säckingen, 12/2018.
M. Voyame/Division manager
2.1 p
rior to tAKing the mAchine into serVice
Before connecting tool to a power
source, be sure the voltage sup-
plied is the same as specified on
the name plate of the tool. The power sup-
ply should not vary more than 10% above or below the
voltage indicated on the nameplate. Check grinding tool
1. n
oteS on
S
afety
2. c
ommISSIonIng
prior to use. The grinding tool must be mounted centrally
and positioned against the limit stop. The maximum al-
lowable speed of the tool and of the chuck may not be
exceeded under any circumstances. Observe national
regulations.
See the corresponding technical document for installing
extension system.
See the corresponding technical document for installing
hand pieces.
2.2 t
AKing the mAchine into serVice
Preselect speed with adjusting wheel according to speed
table.
Level 1: 3800m/s
Level 4: 6500m/s
Level 2: 4700m/s Level 5: 7500m/s
Level 3: 5500m/s Level 6: 8300m/s
During operation never exceed the speed which
has been matched to the grinding tool specifica-
tions!
2.2.1 t
unr on
/t
urn off
The switch must be at the OFF position, i.e. the «0» is
visible. To switch ON the tool, press the switch, and push
it forwards until it engages audibly, i.e. the «1» becomes
bisible. Press the ON/OFF swith to trigger the blocking
and the machine shuts down.
2.3 r
Ating dAtA
Power voltage 120/230/240V, 50/60Hz
Power Input 1050W
Power Output 580W
No-load speed 3800-8300min
-1
Sound pressure level EN 60745 85dB(A), K=3dB
20
CN
PL
CZ
FI
SE
NL
PT
ES
IT
EN
FR
DE
EN