manualshive.com logo in svg

Sub-Zero Wolf Drop-Down Door Series, Руководство по обслуживанию

Поделиться
Скачать
Sub-Zero Wolf Drop-Down Door Series Скачать руководство пользователя страница 37

Page 37

Microwave Drop-down Door Series

Microwave Drop-down Door Series

Troubleshooting

Troubleshooting

4-10

#826151 - Revision A - March, 2016

To determine if the sensor operation is defective, the simplest method is

1

to replace the sensor with a new sensor.
Perform 3E Checks (page 4-2)

2

Remove the AH Sensor

3

Install a new AH Sensor

4

Perform 4R Checks (4-2) except for testing for microwave power.

5

After the microwave is plugged in for two minutes perform the Water

6

Load Cooking Test for AH Sensor.
Measure the resistance from terminal F1 to F3.  At 77° F resistance

7

should be 4 kOhms
Measure the resistance from terminal F2 to F3.  At 77° F resistance

8

should be 2 - 4 kOhms
Measure the resistance from terminal F1 to F2.  At 77° F resistance

9

should be 5 - 7 kOhms

If the turntable motor, high voltage transformer, or fan motor is not operating, 
and live voltage test shows no voltage at the component, test the power to the 
control board.

Perform 3E Checks (page 4-2)

1

Disconnect and isolate the wires to the primary side of the high voltage

2

transformer
Remove CN-A from the control board and connect voltmeter to pins 1 and 3

3

Close the oven door

4

Enter three minutes on the touch pad and energize the microwave, and

5

observe voltage
Perform 3E Checks (page 4-2)

6

Remove voltmeter leads, and connect CN-A to the control board

7

Connect wires to the primary side of the high voltage transformer

8

If line voltage was observed and the turntable motor, high voltage trans-

9

former, and fan motor resistance measures correctly, replace the control
unit.

NOTE: 

If the other motors are working it is assumed there is voltage to the control

unit.

TESTING METHOD FOR AH

SENSOR

RELAY TEST

TEST

PROCEDURE

COMPONENT TEST

Содержание Wolf Drop-Down Door Series














































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды