manualshive.com logo in svg

Stûv 30-up, Руководство по установке

Поделиться
Скачать
Stûv 30-up Скачать руководство пользователя страница 10

10

1

2

4

3

6

5

8

7

Stûv 30-up - installation [en] - 0209 
SN 68 719 > ...

Unpacking and preparation of the stove

Please note

 The paint is not oven 

baked and is therefore relatively 
fragile but will harden after being 
heated a few times. Handle the 
system with care when installing.

Take out the convection column and 
all of the accessories in the back of the 
stove.

The palette is made up of 2 parts. 
Remove the one holding the 
accessories.

To unpack the stove: 
–  remove the fasteners from the 4    
  corners of the box [photo 1]. 
– remove the stove box.

Checking the contents

The stove comes with:

–  the convection column and the 

telescopic duct

–  10 wedges – spray paint

–  installation instructions and 

directions for use in your language

–  the connection set (n° 1 to 6° 

depending on your order)

– other accessories ordered.

Preparing the stove

Lift the upper plate [photo 2].

Unscrew the 2 M5 rounded screws 
with a size 3 Allen key and take off 
the panels [photos 3 and 4].

Also remove the convection column 
support held by these 2 screws 
[photo 5].

Remove the upper finished section of 
the console [photo 6].

Supporting the console, unscrew 
1 screw from each side (key 8) 
[photo 7], lower the console and then 
remove it [photo 8].

Содержание 30-up

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды