Stulz ENS 14 A Скачать руководство пользователя страница 60

Страница: 60 / 110

DE / 06-2016 / 1000687

Start-up

STULZ UltraSonic -System for duct humidification ENS 14 A - 18 A-

Start-up Checklist for STULZ UltraSonic® Humidifiers

The

technical documentation

of all units to be started up and their accessories is to hand

All humidifiers are precisely horizontal and securely mounted

Clearances and distances have been complied with

All units are accessible and operable

All humidifiers have an upstream actuation system

The oscillator PCBs are protected from voltage peaks by a TVS diode. This must be integrated
in the control system.

The electrical wiring is correct and complies with standards

Electrical power is available

Demineralized drinking water is connected to the supply pipe of all humidifiers

All water supply and drainage pipes and the overflow are correctly connected and secured

All accessories (e.g. water treatment system, sensors, fan, …) have been correctly fitted

All pipework channels and shut-off valves are known

Drinking water is available (if reverse osmosis or an ion exchanger is used, otherwise:
demineralized drinking water is available)

Duct units are locked with the airflow

The offtake capacity can be guaranteed by the upstream water softening equipment

The minimum pressure of 0.5 bar at the humidifiers is complied with

The maximum operating pressure of 6 bar at the humidifiers is not exceeded

The conductivity specified for the application is adhered to

Sensitive components are protected from or resistant to demineralized water

The humidifiers are protected from impurities that may arise (dust, pollen, etc.)

The flush valve is installed downstream from the humidifier in the drainage pipe, and is
below the humidifier

__________________________________

Date, signature

TEST REPORT

STULZ GMBH

STULZ UltraSonic®

KLIMATECHNIK

Air Conditioning & Humidifying
Systems Division
Phone

+49 (0)40 55 85 252

Fax

+49 (0)40 55 01 315

KTR No.:

Test performed by:

Date:

Customer name:

Address, zip code, city:

Order:

Contact:

Phone:

Unit type: Ultrasonic humidifier



BNB



ENS



SCA



Unit name:

Serial no.:

Error message:

Electrical supply:



230V/1Ph/50Hz



Comments:

Reason for test



Start-up



Service



Fault

General condition

(before the test)



Very good



Good



Adequate



Poor

Electrical test of humidifier

Solenoid fill valve



Damaged/tight



Comments:

Oscillators

Circuit 1



Damaged



Comments:

Oscillators

Circuit 2



Damaged



Comments:

Fan module



Damaged



Comments:

Safety chain

Low level float switch



Damaged



Comments:

Supply float switch



Damaged/tight



Comments:

Auxiliary relay on PCB



Damaged



Comments:

Thermostat



Damaged



Comments:

Water contact loop (ENS14+18)



Damaged



Comments:

Ultrasonic Humidifier

STULZ GmbH Klimatechnik

Holsteiner Chaussee 283

22457 Hamburg, Germany

Company headquarters is Hamburg

Hamburg District Court HRB 16255

VAT ID No. DE 811 207 224

Directors: J. Stulz (Chairman),

Dr. U. Görge, M. Stulz,

M. Zimmermann

S-Klima

Job to be performed

Page Procedure and maintenance interval

Date

Signature

Date

Signature

Date

Signature

OK*

Visual inspection

75 -

Tightness of connections of water-bearing parts

Cleanness of filter

Outside of unit for impurities

Water tank for impurities, damage, microbial growth and

corrosion

Humidity sensor and ventilation slots for impurities

Solenoid valves for deposits

Every 3 months**

☐

77 -

Check oscillators for deposits

Check mist guide pipes for deposits

Every 6 months**

☐

Leak test

Inspect all screw and push-in connections for leaks and a secure fit

Every 6 months**

☐

Clean the water tank

Remove housing cover and retaining plate together with mist

guide pipes (open water tank), clean and

disinfect with hydrogen peroxide solution

Every 6 months**

☐

Inspect the electrical

system

Remove cover of control system and check electrics

Every 6 months**

☐

Replace float switches

Open water tank, remove float switch and fill valve unit

Approx. every 10,000 operating hours**

☐

Replace oscillators

Remove water tank, disconnect cables, detach oscillators

Approx. every 10,000 operating hours**

☐

Delete as applicable

Time intervals may be shorter in isolated cases, depending on local conditions

8.1.

Reports and checklists for STULZ UltraSonic humidifiers

We have provided you with a checklist to facilitate start-up. You can find the Start-up Checklist, Test

Report and Maintenance Checklist on the final pages of this manual or available to download on our web

site at

www.stulz.com

Содержание ENS 14 A















































































































Результаты поиска

Содержание ENS 14 A

Отзывы:

Похожие инструкции для ENS 14 A

Бренды по названию

Популярные бренды

Stulz ENS 14 A, Техническое руководство

Результаты поиска

Содержание ENS 14 A

Отзывы:

Похожие инструкции для ENS 14 A

Бренды по названию

Популярные бренды