Studer VarioString VS-120 Скачать руководство пользователя страница 35

Страница: 35 / 64

Studer Innotec SA

VarioString

User manual

V 2.3

Level

User

ref. Parameter

Factory value

Expert 14037 SYSTEM

Expert 14174 Block manual programming (dip-switch)

Expert 14040 Type of battery grounding

No control

Expert 14194 Configuration for VS-120

Expert 14041 Type of PV grounding

No control

Expert 14175 Type of PV1 grounding

No control

Expert 14042 Type of PV2 grounding

No control

Expert 14180 Type of MPPT algorithm

Expert 14043 Type of MPP tracking algorithm PV

LSF

Expert 14044 PV voltage fixed (for PV in series)

700 Vdc

Expert 14179 PV voltage fixed (for PV in //)

500 Vdc

Expert 14045 Ratio of PV open circuit voltage

0.7

Expert 14176 Type of MPP tracking algorithm PV1

LSF

Expert 14177 PV1 voltage fixed

500 Vdc

Expert 14178 Ratio of PV1 open circuit voltage

0.7

Expert 14046 Type of MPP tracking algorithm PV2

LSF

Expert 14047 PV2 voltage fixed

500 Vdc

Expert 14048 Ratio of PV2 open circuit voltage

0.7

Inst.

14192 Establishment time (Algo MPPT)

0 sec

Inst.

14193 Averaging time (algo MPPT)

0 sec

Inst.

14190 PV wiring type erased from memory

Expert 14195 Configuration for VS-70

Expert 14196 Type of PV grounding

No control

Expert 14180 Type of MPPT algorithm

Expert 14197 Type of MPP tracking algorithm PV

LSF

Expert 14198 PV voltage fixed

500 Vdc

Expert 14199 Ratio of PV open circuit voltage

0.7

Inst.

14192 Establishment time (Algo MPPT)

0 sec

Inst.

14193 Averaging time (algo MPPT)

0 sec

Expert 14200 Remote entry (Remote ON/OFF)

Expert 14201 Remote entry active

Open

Expert 14202 ON/OFF command

Expert 14203 Activated by AUX1 state

Expert 14204 Start equalization

Expert 14205 Send a message when remote entry changes state

Inst.

14218 VarioString watchdog enabled (SCOM)

Inst.

14219 VarioString watchdog delay (SCOM)

60 sec

Expert 14182 Reset PV energy meter

Expert 14051 Reset daily solar production meters

Expert 14052 Reset daily min-max

Basic

14067 Restore default settings

Inst.

14068 Restore factory settings

Inst.

14069 Parameters saved in flash memory

Yes

Expert 14038 ON of the VarioString

Expert 14039 OFF of the VarioString

Expert 14059 Reset of all VarioString

9.4.3.1

Auxiliary relay parameters

A list of the auxiliary relay parameters can be found at the end of this manual in chapters 9.4.7 and
17.

Содержание VarioString VS-120

































































Результаты поиска

Содержание VarioString VS-120

Отзывы:

Похожие инструкции для VarioString VS-120

Бренды по названию

Популярные бренды

Studer VarioString VS-120, Руководство пользователя

Результаты поиска

Содержание VarioString VS-120

Отзывы:

Похожие инструкции для VarioString VS-120

Бренды по названию

Популярные бренды